The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:

cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.

This patch applies the operating points to each cpu of the A33.

Fixes: 03749eb ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The manufacturing information is stored in the EEPROM.  This chip
is an AT24C64 not not (nor has it ever been) 24C02.  This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).

Fixes: 5e3447a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Though cpsw doesn't support EEE feature, Atheros 8035 provides
automatic EEE support that is enabled by default. This causes
occasional link drops when link partner also announces EEE support.
These link drops occur on both 100Mbit/s and 1000Mbit/s speeds.
So disable EEE advertising completely.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

dtc recently added PCI bus checks. Fix these warnings.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 3251885 ("ARM: OMAP4+: Reset CPU1 properly for kexec") started
unconditionally resetting CPU1 because of a kexec boot issue I was seeing
earlier on omap4 when doing kexec boot between two different kernel
versions.

This caused issues on some systems. We should only reset CPU1 as a last
resort option, and try to avoid it where possible. Doing an unconditional
CPU1 reset causes issues for example when booting a bootloader configured
secure OS running on CPU1 as reported by Andrew F. Davis <afd@ti.com>.

We can't completely remove the reset of CPU1 as it would break kexec
booting from older kernels. But we can limit the CPU1 reset to cases
where CPU1 is wrongly parked within the memory area used by the booting
kernel. Then later on we can add support for parking CPU1 for kexec out
of the SDRAM back to bootrom.

So let's first fix the regression reported by Andrew by making CPU1 reset
conditional. To do this, we need to:

1. Save configured AUX_CORE_BOOT_1 for later

2. Modify AUX_CORE_BOOT_0 reading code to for HS SoCs to return
   the whole register instead of the CPU mask

3. Check if CPU1 is wrongly parked into the booting kernel by the
   previous kernel and reset if needed

Fixes: 3251885 ("ARM: OMAP4+: Reset CPU1 properly for kexec")
Reported-by: Andrew F. Davis <afd@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Tested-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

…comparison)

While reviewing the -stable patch for commit 86ef58a "nfit,
libnvdimm: fix interleave set cookie calculation" Ben noted:

    "This is returning an int, thus it's effectively doing a 32-bit
     comparison and not the 64-bit comparison you say is needed."

Update the compare operation to be immune to this integer demotion problem.

Cc: <stable@vger.kernel.org>
Cc: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Fixes: 86ef58a ("nfit, libnvdimm: fix interleave set cookie calculation")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

In commit 6afaf8a ("UBI: flush wl before clearing update marker") I
managed to trigger and fix a similar bug. Now here is another version of
which I assumed it wouldn't matter back then but it turns out UBI has a
check for it and will error out like this:

|ubi0 warning: validate_vid_hdr: inconsistent used_ebs
|ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592

All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a
powercut in the middle of the operation.
ubi_start_update() sets the update-marker and puts all EBs on the erase
list. After that userland can proceed to write new data while the old EB
aren't erased completely. A powercut at this point is usually not that
much of a tragedy. UBI won't give read access to the static volume
because it has the update marker. It will most likely set the corrupted
flag because it misses some EBs.
So we are all good. Unless the size of the image that has been written
differs from the old image in the magnitude of at least one EB. In that
case UBI will find two different values for `used_ebs' and refuse to
attach the image with the error message mentioned above.

So in order not to get in the situation, the patch will ensure that we
wait until everything is removed before it tries to write any data.
The alternative would be to detect such a case and remove all EBs at the
attached time after we processed the volume-table and see the
update-marker set. The patch looks bigger and I doubt it is worth it
since usually the write() will wait from time to time for a new EB since
usually there not that many spare EB that can be used.

Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>

When fscrypt_setup_filename() fails we have to free dev.

Signed-off-by: Richard Weinberger <richard@nod.at>

if filename is encrypted, filename could have no printable characters.
so remove it.

Signed-off-by: Hyunchul Lee <cheol.lee@lge.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

if a character is not printable, print '?' instead of that.

Signed-off-by: Hyunchul Lee <cheol.lee@lge.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

instead of filenames, print inode numbers, file types, and length.

Signed-off-by: Hyunchul Lee <cheol.lee@lge.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Remove faulty leftover check in do_rename(), apparently introduced in a
merge that combined whiteout support changes with commit f03b8ad
("fs: support RENAME_NOREPLACE for local filesystems")

Fixes: f03b8ad ("fs: support RENAME_NOREPLACE for local
filesystems")
Fixes: 9e0a1ff ("ubifs: Implement RENAME_WHITEOUT")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Richard Weinberger <richard@nod.at>

Board code cannot call mdiobus_register_board_info() when phylib
or mdio_device is a loadable module:

arch/arm/plat-orion/common.o: In function `orion_ge00_switch_init':
:(.init.text+0x474): undefined reference to `mdiobus_register_board_info'

I had a number of ideas for how this could be solved, but after the MDIO
code got split out from PHYLIB it has gotten too hard, so I'm basically
giving up, and only call the mdiobus_register_board_info() function
if the MDIO layer is built-in to avoid the link error. This is similar
to how we handle PHY registration on other ARM platforms.

Fixes: 90eff90 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea01 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

A dump may come in the middle of another dump, modifying its dump
structure members. This race condition will result in NULL pointer
dereference in kernel. So add a lock to prevent that race.

Fixes: 83321d6 ("[AF_KEY]: Dump SA/SP entries non-atomically")
Signed-off-by: Yuejie Shi <syjcnss@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

0000: PLLQ = 0, wrong configuration
0001: PLLQ = 1, wrong configuration
...
0010: PLLQ = 2
0011: PLLQ = 3
0100: PLLQ = 4
...
1111: PLLQ = 1

Use divider table to exclude 0 and 1 values.

Fixes: 83135ad ("clk: stm32f4: Add PLL_I2S & PLL_SAI for STM32F429/469 boards")

Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Rename the internal __reset_control_get/put functions to
__reset_control_get/put_internal and add an exported
__reset_control_get equivalent to __of_reset_control_get
that takes a struct device parameter.
This avoids the confusing call to __of_reset_control_get in
the non-DT case and fixes the devm_reset_control_get_optional
function to return NULL if RESET_CONTROLLER is enabled but
dev->of_node == NULL.

Fixes: bb47523 ("reset: make optional functions really optional")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

… defer

Starting from commit 5de85b9 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.

This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:

omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?

We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.

Fixes: 5de85b9 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit a1f3e4d "libnvdimm, region: update nd_region_available_dpa()
for multi-pmem support" reworked blk dpa (DIMM Physical Address)
accounting to comprehend multiple pmem namespace allocations aliasing
with a given blk-dpa range.

The following call trace is a result of failing to account for allocated
blk capacity.

 WARNING: CPU: 1 PID: 2433 at tools/testing/nvdimm/../../../drivers/nvdimm/names
4 size_store+0x6f3/0x930 [libnvdimm]
 nd_region region5: allocation underrun: 0x0 of 0x1000000 bytes
 [..]
 Call Trace:
  dump_stack+0x86/0xc3
  __warn+0xcb/0xf0
  warn_slowpath_fmt+0x5f/0x80
  size_store+0x6f3/0x930 [libnvdimm]
  dev_attr_store+0x18/0x30

If a given blk-dpa allocation does not alias with any pmem ranges then
the full allocation should be accounted as busy space, not the size of
the current pmem contribution to the region.

The thinkos that led to this confusion was not realizing that the struct
resource management is already guaranteeing no collisions between pmem
allocations and blk allocations on the same dimm. Also, we do not try to
support blk allocations in aliased pmem holes.

This patch also fixes a case where the available blk goes negative.

Cc: <stable@vger.kernel.org>
Fixes: a1f3e4d ("libnvdimm, region: update nd_region_available_dpa() for multi-pmem support").
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

At a commit 6c29230 ("ALSA: oxfw: delayed registration of sound
card"), ALSA oxfw driver fails to handle SCS.1m/1d, due to -EBUSY at a call
of snd_card_register(). The cause is that the driver manages to register
two rawmidi instances with the same device number 0. This is a regression
introduced since kernel 4.7.

This commit fixes the regression, by fixing up device property after
discovering stream formats.

Fixes: 6c29230 ("ALSA: oxfw: delayed registration of sound card")
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The USB PHY in A64 has a "pmu0" region, which controls the EHCI/OHCI
controller pair that can be connected to the PHY0.

Add the MMIO region for PHY node.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

With RTlinux a race condition has been found that leads to NULL ptr crash:
- On CPU 0: uni_player_irq_handler is called to treat XRUN
 "(player->state == UNIPERIF_STATE_STOPPED)" is FALSE so status is checked,
 dev_err(player->dev, "FIFO underflow error detected") is printed
and then snd_pcm_stream_lock should be called to lock stream for stopping.
- On CPU 1: application stop and close the stream.
Issue is that the stop and shutdown functions are executed while
"FIFO underflow error detected" is printed.
So when CPU 0 calls snd_pcm_stream_lock, player->substream is already null.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.

[mkp: tweaked to avoid setting rw_max twice and added typecast]

Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ca369d5 ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.

Cc: <stable@vger.kernel.org>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We need to initialize qedf->fipvlan_compl in __qedf_probe so that if we
receive an unsolicited FIP VLAN response, the system doesn't crash due
to trying to complete an uninitialized completion.

Also add a check to see if there are any waiters on the completion so we
don't inadvertantly kick start the discovery process due to the
unsolicited frame.

Fixed the crash:

<1>BUG: unable to handle kernel NULL pointer dereference at (null)
<1>IP: [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>PGD 0
<4>Oops: 0000 [#1] SMP
<4>last sysfs file: /sys/devices/system/cpu/online
<4>CPU 7
<4>Modules linked in: autofs4 nfs lockd fscache auth_rpcgss nfs_acl sunrpc target_core_iblock target_core_file target_core_pscsi target_core_mod configfs bnx2fc cnic fcoe 8021q garp stp llc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 vfat fat uinput ipmi_devintf microcode power_meter acpi_ipmi ipmi_si ipmi_msghandler iTCO_wdt iTCO_vendor_support dcdbas sg joydev sb_edac edac_core lpc_ich mfd_core shpchp tg3 ptp pps_core ext4 jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif qedi(U) iscsi_boot_sysfs libiscsi scsi_transport_iscsi uio qedf(U) libfcoe libfc scsi_transport_fc scsi_tgt qede(U) qed(U) ahci megaraid_sas wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: speedstep_lib]
<4>
<4>Pid: 1485, comm: qedf_11_ll2 Not tainted 2.6.32-642.el6.x86_64 #1 Dell Inc. PowerEdge R730/0599V5
<4>RIP: 0010:[<ffffffff8105ed71>]  [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>RSP: 0018:ffff881068a83d50  EFLAGS: 00010086
<4>RAX: ffffffffffffffe8 RBX: ffff88106bf42de0 RCX: 0000000000000000
<4>RDX: 0000000000000000 RSI: 0000000000000003 RDI: ffff88106bf42de0
<4>RBP: ffff881068a83d90 R08: 0000000000000000 R09: 00000000fffffffe
<4>R10: 0000000000000000 R11: 000000000000000b R12: 0000000000000286
<4>R13: ffff88106bf42de8 R14: 0000000000000000 R15: 0000000000000000
<4>FS:  0000000000000000(0000) GS:ffff88089c460000(0000) knlGS:0000000000000000
<4>CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<4>CR2: 0000000000000000 CR3: 0000000001a8d000 CR4: 00000000001407e0
<4>DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4>DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>Process qedf_11_ll2 (pid: 1485, threadinfo ffff881068a80000, task ffff881068a70040)
<4>Stack:
<4> ffff88106ef00090 0000000300000001 ffff881068a83d90 ffff88106bf42de0
<4><d> 0000000000000286 ffff88106bf42dd8 ffff88106bf40a50 0000000000000002
<4><d> ffff881068a83dc0 ffffffff810634c7 ffff881000000003 000000000000000b
<4>Call Trace:
<4> [<ffffffff810634c7>] complete+0x47/0x60
<4> [<ffffffffa01d37e7>] qedf_fip_recv+0x1c7/0x450 [qedf]
<4> [<ffffffffa01cb3cb>] qedf_ll2_recv_thread+0x33b/0x510 [qedf]
<4> [<ffffffffa01cb090>] ? qedf_ll2_recv_thread+0x0/0x510 [qedf]
<4> [<ffffffff810a662e>] kthread+0x9e/0xc0
<4> [<ffffffff8100c28a>] child_rip+0xa/0x20
<4> [<ffffffff810a6590>] ? kthread+0x0/0xc0
<4> [<ffffffff8100c280>] ? child_rip+0x0/0x20
<4>Code: 41 56 41 55 41 54 53 48 83 ec 18 0f 1f 44 00 00 89 75 cc 89 55 c8 4c 8d 6f 08 48 8b 57 08 41 89 cf 4d 89 c6 48 8d 42 e8 49 39 d5 <48> 8b 58 18 74 3f 48 83 eb 18 eb 0a 0f 1f 00 48 89 d8 48 8d 5a
<1>RIP  [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4> RSP <ffff881068a83d50>
<4>CR2: 0000000000000000

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.

Fixes: a465537 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.

Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.

Cc: <stable@vger.kernel.org>
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

…a/linux into fixes

Reset controller fixes for v4.11

Fix devm_reset_controller_get_optional to return NULL for non-DT devices,
if the RESET_CONTROLLER Kconfig option is enabled. This fixes probe failures
of the 8250_dw driver on Intel platforms after commit acbdad8 ("serial:
8250_dw: simplify optional reset handling").

* tag 'reset-fixes-for-4.11-2' of git://git.pengutronix.de/git/pza/linux:
  reset: add exported __reset_control_get, return NULL if optional

Signed-off-by: Olof Johansson <olof@lixom.net>

…linux/kernel/git/sunxi/linux into fixes

Allwinner fixes for 4.11, bis

Two fixes for the recent A33 cpufreq support, and one to fix a missing
register in the A64 USB PHY node.

* tag 'sunxi-fixes-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: a64: add pmu0 regs for USB PHY
  ARM: sun8i: a33: add operating-points-v2 property to all nodes
  ARM: sun8i: a33: remove highest OPP to fix CPU crashes

Signed-off-by: Olof Johansson <olof@lixom.net>

The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY.  Drop these
superfluous flags for fixing the behavior.

Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:

  BUG: scheduling while atomic: systemd-sleep/3144/0x00000003
  Call Trace:
   dump_stack+0x5c/0x7a
   __schedule_bug+0x55/0x70
   __schedule+0x63c/0x8c0
   schedule+0x3d/0x90
   schedule_timeout+0x16b/0x320
   ? del_timer_sync+0x50/0x50
   ? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
   ? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
   ? remove_wait_queue+0x60/0x60
   ? sst_prepare_and_post_msg+0x275/0x960 [snd_intel_sst_core]
   ? sst_pause_stream+0x9b/0x110 [snd_intel_sst_core]
   ....

This patch addresses these appropriately, too.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.1+

Fixes: dd248f1 ("sfc: Add PCI ID for Solarflare 8000 series 10/40G NIC")
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

…/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-04-25

this is a pull request of three patches for net/master.

There are two patches by Stephane Grosjean for that add a new variant to the
PCAN-Chip USB driver. The other patch is by Maksim Salau, which swtiches the
memory for USB transfers from heap to stack.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

…and 'asoc/fix/sti' into asoc-linus

In functions team_nl_send_port_list_get() and
team_nl_send_options_get(), pointer skb keeps the return value of
nlmsg_new(). When the call to genlmsg_put() fails, the memory is not
freed(). This will result in memory leak bugs.

Fixes: 9b00cf2 ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ipv6 stub pointer is currently initialized before the ipv6
routing subsystem: a 3rd party can access and use such stub
before the routing data is ready.
Moreover, such pointer is not cleared in case of initialization
error, possibly leading to dangling pointers usage.

This change addresses the above moving the stub initialization
at the end of ipv6 init code.

Fixes: 5f81bd2 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

…kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.11

A few last minute fixes for v4.11, the STI fix is relatively large but
driver specific and has been cooking in -next for a little while now:

 - A fix from Takashi for some suspend/resume related crashes in the
   Intel drivers.
 - A fix from Mousumi Jana for issues with incorrectly created
   enumeration controls generated from topology files which could cause
   problems for userspace.
 - Fixes from Arnaud Pouliquen for some crashes due to races with the
   interrupt handler in the STI driver.

Until now in tipc_send_stream(), we return -1 when the socket
encounters link congestion even if the socket had successfully
sent partial data. This is incorrect as the application resends
the same the partial data leading to data corruption at
receiver's end.

In this commit, we return the partially sent bytes as the return
value at link congestion.

Fixes: 10724cc ("tipc: redesign connection-level flow control")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now in tipc_recv_stream(), we update the received
unacknowledged bytes based on a stack variable and not based on the
actual message size.
If the user buffer passed at tipc_recv_stream() is smaller than the
received skb, the size variable in stack differs from the actual
message size in the skb. This leads to a flow control accounting
error causing permanent congestion.

In this commit, we fix this accounting error by always using the
size of the incoming message.

Fixes: 10724cc ("tipc: redesign connection-level flow control")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

keep tty driver until usb driver is unregistered
rmmod hso
produces traces like this without that:

[40261.645904] usb 2-2: new high-speed USB device number 2 using ehci-omap
[40261.854644] usb 2-2: New USB device found, idVendor=0af0, idProduct=8800
[40261.862609] usb 2-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[40261.872772] usb 2-2: Product: Globetrotter HSUPA Modem
[40261.880279] usb 2-2: Manufacturer: Option N.V.
[40262.021270] hso 2-2:1.5: Not our interface
[40265.556945] hso: unloaded
[40265.559875] usbcore: deregistering interface driver hso
[40265.595947] Unable to handle kernel NULL pointer dereference at virtual address 00000033
[40265.604522] pgd = ecb14000
[40265.611877] [00000033] *pgd=00000000
[40265.617034] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[40265.622650] Modules linked in: hso(-) bnep bluetooth ipv6 arc4 twl4030_madc_hwmon wl18xx wlcore mac80211 cfg80211 snd_soc_simple_card snd_soc_simple_card_utils snd_soc_omap_twl4030 snd_soc_gtm601 generic_adc_battery extcon_gpio omap3_isp videobuf2_dma_contig videobuf2_memops wlcore_sdio videobuf2_v4l2 videobuf2_core ov9650 bmp280_i2c v4l2_common bmp280 bmg160_i2c bmg160_core at24 nvmem_core videodev bmc150_accel_i2c bmc150_magn_i2c media bmc150_accel_core tsc2007 bmc150_magn leds_tca6507 bno055 snd_soc_omap_mcbsp industrialio_triggered_buffer snd_soc_omap kfifo_buf snd_pcm_dmaengine gpio_twl4030 snd_soc_twl4030 twl4030_vibra twl4030_madc wwan_on_off ehci_omap pwm_bl pwm_omap_dmtimer panel_tpo_td028ttec1 encoder_opa362 connector_analog_tv omapdrm drm_kms_helper cfbfillrect syscopyarea cfbimgblt sysfillrect
[40265.698211]  sysimgblt fb_sys_fops cfbcopyarea drm omapdss usb_f_ecm g_ether usb_f_rndis u_ether libcomposite configfs omap2430 phy_twl4030_usb musb_hdrc twl4030_charger industrialio w2sg0004 twl4030_pwrbutton bq27xxx_battery w1_bq27000 omap_hdq [last unloaded: hso]
[40265.723175] CPU: 0 PID: 2701 Comm: rmmod Not tainted 4.11.0-rc6-letux+ #6
[40265.730346] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[40265.736938] task: ecb81100 task.stack: ecb82000
[40265.741729] PC is at cdev_del+0xc/0x2c
[40265.745666] LR is at tty_unregister_device+0x40/0x50
[40265.750915] pc : [<c027472c>]    lr : [<c04b3ecc>]    psr: 600b0113
sp : ecb83ea8  ip : eca4f898  fp : 00000000
[40265.763000] r10: 00000000  r9 : 00000000  r8 : 00000001
[40265.768493] r7 : eca4f800  r6 : 00000003  r5 : 00000000  r4 : ffffffff
[40265.775360] r3 : c1458d54  r2 : 00000000  r1 : 00000004  r0 : ffffffff
[40265.782257] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[40265.789764] Control: 10c5387d  Table: acb14019  DAC: 00000051
[40265.795806] Process rmmod (pid: 2701, stack limit = 0xecb82218)
[40265.802062] Stack: (0xecb83ea8 to 0xecb84000)
[40265.806640] 3ea0:                   ec9e8100 c04b3ecc bf737378 ed5b7c00 00000003 bf7327ec
[40265.815277] 3ec0: eca4f800 00000000 ec9fd800 eca4f800 bf737070 bf7328bc eca4f820 c05a9a04
[40265.823883] 3ee0: eca4f820 00000000 00000001 eca4f820 ec9fd870 bf737070 eca4f854 ec9fd8a4
[40265.832519] 3f00: ecb82000 00000000 00000000 c04e6960 eca4f820 bf737070 bf737048 00000081
[40265.841125] 3f20: c01071e4 c04e6a60 ecb81100 bf737070 bf737070 c04e5d94 bf737020 c05a8f88
[40265.849731] 3f40: bf737100 00000800 7f5fa254 00000081 c01071e4 c01c4afc 00000000 006f7368
[40265.858367] 3f60: ecb815f 00000000 c0cac9c4 c01071e4 ecb82000 00000000 00000000 c01512f4
[40265.866973] 3f80: ed5b3200 c01071e4 7f5fa220 7f5fa220 bea78ec9 0010711c 7f5fa220 7f5fa220
[40265.875579] 3fa0: bea78ec9 c0107040 7f5fa220 7f5fa220 7f5fa254 00000800 dd35b800 dd35b800
[40265.884216] 3fc0: 7f5fa220 7f5fa220 bea78ec9 00000081 bea78dcc 00000000 bea78bd8 00000000
[40265.892822] 3fe0: b6f70521 bea78b6c 7f5dd613 b6f70526 80070030 7f5fa254 ffffffff ffffffff
[40265.901458] [<c027472c>] (cdev_del) from [<c04b3ecc>] (tty_unregister_device+0x40/0x50)
[40265.909942] [<c04b3ecc>] (tty_unregister_device) from [<bf7327ec>] (hso_free_interface+0x80/0x144 [hso])
[40265.919982] [<bf7327ec>] (hso_free_interface [hso]) from [<bf7328bc>] (hso_disconnect+0xc/0x18 [hso])
[40265.929718] [<bf7328bc>] (hso_disconnect [hso]) from [<c05a9a04>] (usb_unbind_interface+0x84/0x200)
[40265.939239] [<c05a9a04>] (usb_unbind_interface) from [<c04e6960>] (device_release_driver_internal+0x138/0x1cc)
[40265.949798] [<c04e6960>] (device_release_driver_internal) from [<c04e6a60>] (driver_detach+0x60/0x6c)
[40265.959503] [<c04e6a60>] (driver_detach) from [<c04e5d94>] (bus_remove_driver+0x64/0x8c)
[40265.968017] [<c04e5d94>] (bus_remove_driver) from [<c05a8f88>] (usb_deregister+0x5c/0xb8)
[40265.976654] [<c05a8f88>] (usb_deregister) from [<c01c4afc>] (SyS_delete_module+0x160/0x1dc)
[40265.985443] [<c01c4afc>] (SyS_delete_module) from [<c0107040>] (ret_fast_syscall+0x0/0x1c)
[40265.994171] Code: c1458d54 e59f3020 e92d401 e1a04000 (e5941034)
[40266.016693] ---[ end trace 9d5ac43c7e41075c ]---

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

My change (introduced in 4.11) to use find_first_clear_bit
incorrectly assumed that the size argument was words, not bits.
The effect was only a small limited number of the available send
sections were being actually used. This can cause performance loss
with some workloads.

Since map_words is now used only during initialization, it can
be on stack instead of in per-device data.

Fixes: b58a185 ("netvsc: simplify get next send section")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DCBX app_data array is initialized with the incorrect values for
personality field. This would  prevent offloaded protocols from
honoring the PFC.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a149e7c ("ipv6: sr: add support for SRH injection through
setsockopt") introduced handling of IPV6_SRCRT_TYPE_4, but at the same
time restricted it to only IPV6_SRCRT_TYPE_0 and
IPV6_SRCRT_TYPE_4. Previously, ipv6_push_exthdr() and fl6_update_dst()
would also handle other values (ie STRICT and TYPE_2).

Restore previous source routing behavior, by handling IPV6_SRCRT_STRICT
and IPV6_SRCRT_TYPE_2 the same way as IPV6_SRCRT_TYPE_0 in
ipv6_push_exthdr() and fl6_update_dst().

Fixes: a149e7c ("ipv6: sr: add support for SRH injection through setsockopt")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

During removing a bridge device, if the bridge is still up, a new mdb entry
still can be added in br_multicast_add_group() after all mdb entries are
removed in br_multicast_dev_del(). Like the path:

  mld_ifc_timer_expire ->
    mld_sendpack -> ...
      br_multicast_rcv ->
        br_multicast_add_group

The new mp's timer will be set up. If the timer expires after the bridge
is freed, it may cause use-after-free panic in br_multicast_group_expired.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa07ed2c8>] br_multicast_group_expired+0x28/0xb0 [bridge]
Call Trace:
 <IRQ>
 [<ffffffff81094536>] call_timer_fn+0x36/0x110
 [<ffffffffa07ed2a0>] ? br_mdb_free+0x30/0x30 [bridge]
 [<ffffffff81096967>] run_timer_softirq+0x237/0x340
 [<ffffffff8108dcbf>] __do_softirq+0xef/0x280
 [<ffffffff8169889c>] call_softirq+0x1c/0x30
 [<ffffffff8102c275>] do_softirq+0x65/0xa0
 [<ffffffff8108e055>] irq_exit+0x115/0x120
 [<ffffffff81699515>] smp_apic_timer_interrupt+0x45/0x60
 [<ffffffff81697a5d>] apic_timer_interrupt+0x6d/0x80

Nikolay also found it would cause a memory leak - the mdb hash is
reallocated and not freed due to the mdb rehash.

unreferenced object 0xffff8800540ba800 (size 2048):
  backtrace:
    [<ffffffff816e2287>] kmemleak_alloc+0x67/0xc0
    [<ffffffff81260bea>] __kmalloc+0x1ba/0x3e0
    [<ffffffffa05c60ee>] br_mdb_rehash+0x5e/0x340 [bridge]
    [<ffffffffa05c74af>] br_multicast_new_group+0x43f/0x6e0 [bridge]
    [<ffffffffa05c7aa3>] br_multicast_add_group+0x203/0x260 [bridge]
    [<ffffffffa05ca4b5>] br_multicast_rcv+0x945/0x11d0 [bridge]
    [<ffffffffa05b6b10>] br_dev_xmit+0x180/0x470 [bridge]
    [<ffffffff815c781b>] dev_hard_start_xmit+0xbb/0x3d0
    [<ffffffff815c8743>] __dev_queue_xmit+0xb13/0xc10
    [<ffffffff815c8850>] dev_queue_xmit+0x10/0x20
    [<ffffffffa02f8d7a>] ip6_finish_output2+0x5ca/0xac0 [ipv6]
    [<ffffffffa02fbfc6>] ip6_finish_output+0x126/0x2c0 [ipv6]
    [<ffffffffa02fc245>] ip6_output+0xe5/0x390 [ipv6]
    [<ffffffffa032b92c>] NF_HOOK.constprop.44+0x6c/0x240 [ipv6]
    [<ffffffffa032bd16>] mld_sendpack+0x216/0x3e0 [ipv6]
    [<ffffffffa032d5eb>] mld_ifc_timer_expire+0x18b/0x2b0 [ipv6]

This could happen when ip link remove a bridge or destroy a netns with a
bridge device inside.

With Nikolay's suggestion, this patch is to clean up bridge multicast in
ndo_uninit after bridge dev is shutdown, instead of br_dev_delete, so
that netif_running check in br_multicast_add_group can avoid this issue.

v1->v2:
  - fix this issue by moving br_multicast_dev_del to ndo_uninit, instead
    of calling dev_close in br_dev_delete.

(NOTE: Depends upon b6fe044 ("bridge: implement missing ndo_uninit()"))

Fixes: e10177a ("bridge: multicast: fix handling of temp and perm entries")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Taking down the loopback device wreaks havoc on IPv6 routing. By
extension, taking down a VRF device wreaks havoc on its table.

Dmitry and Andrey both reported heap out-of-bounds reports in the IPv6
FIB code while running syzkaller fuzzer. The root cause is a dead dst
that is on the garbage list gets reinserted into the IPv6 FIB. While on
the gc (or perhaps when it gets added to the gc list) the dst->next is
set to an IPv4 dst. A subsequent walk of the ipv6 tables causes the
out-of-bounds access.

Andrey's reproducer was the key to getting to the bottom of this.

With IPv6, host routes for an address have the dst->dev set to the
loopback device. When the 'lo' device is taken down, rt6_ifdown initiates
a walk of the fib evicting routes with the 'lo' device which means all
host routes are removed. That process moves the dst which is attached to
an inet6_ifaddr to the gc list and marks it as dead.

The recent change to keep global IPv6 addresses added a new function,
fixup_permanent_addr, that is called on admin up. That function restarts
dad for an inet6_ifaddr and when it completes the host route attached
to it is inserted into the fib. Since the route was marked dead and
moved to the gc list, re-inserting the route causes the reported
out-of-bounds accesses. If the device with the address is taken down
or the address is removed, the WARN_ON in fib6_del is triggered.

All of those faults are fixed by regenerating the host route if the
existing one has been moved to the gc list, something that can be
determined by checking if the rt6i_ref counter is 0.

Fixes: f1705ec ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case getsockopt() is called with PACKET_HDRLEN and optlen < 4
|val| remains uninitialized and the syscall may behave differently
depending on its value, and even copy garbage to userspace on certain
architectures. To fix this we now return -EINVAL if optlen is too small.

This bug has been detected with KMSAN.

Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

…el/git/vgupta/arc

Pull ARC fix from Vineet Gupta:
 "Last minute fixes for ARC:

   - build error in Mellanox nps platform

   - addressing lack of saving FPU regs in releavnt configs"

* tag 'arc-4.11-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARCv2: entry: save Accumulator register pair (r58:59) if present
  ARC: [plat-eznps] Fix build error

…it/tiwai/sound

Pull sound fixes from Takashi Iwai:
 "Since we got a bonus week, let me try to screw a few pending fixes.

  A slightly large fix is the locking fix in ASoC STI driver, but it's
  pretty board-specific, and the risk is fairly low.

  All the rest are small / trivial fixes, mostly marked as stable, for
  ALSA sequencer core, ASoC topology, ASoC Intel bytcr and Firewire
  drivers"

* tag 'sound-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: intel: Fix PM and non-atomic crash in bytcr drivers
  ALSA: firewire-lib: fix inappropriate assignment between signed/unsigned type
  ALSA: seq: Don't break snd_use_lock_sync() loop by timeout
  ASoC: topology: Fix to store enum text values
  ASoC: STI: Fix null ptr deference in IRQ handler
  ALSA: oxfw: fix regression to handle Stanton SCS.1m/1d

The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.

The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.

During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.

Fixes: 321beec ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 99f81af.

It was papering over the real problem, which is fixed by commit
f555f34 ("net: phy: fix auto-negotiation stall due to unavailable
interrupt")

Signed-off-by: David S. Miller <davem@davemloft.net>

We call skb_cow_data, which is good anyway to ensure we can actually
modify the skb as such (another error from prior). Now that we have the
number of fragments required, we can safely allocate exactly that amount
of memory.

Fixes: c09440f ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added NULL check to make __dev_kfree_skb_irq consistent with kfree
family of functions.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=195289

Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:

        neigh = dst_neigh_lookup(skb_dst(skb),
                                 &ipv6_hdr(skb)->daddr);
        if (!neigh)
                goto tx_err_link_failure;

        addr6 = (struct in6_addr *)&neigh->primary_key; // <=== HERE
        addr_type = ipv6_addr_type(addr6);

        if (addr_type == IPV6_ADDR_ANY)
                addr6 = &ipv6_hdr(skb)->daddr;

        memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));

Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.

This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.

Fixes: ea3dc96 ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Always zero out ca_priv data in tcp_assign_congestion_control() so that
ca_priv data is cleared out during socket creation.
Also always zero out ca_priv data in tcp_reinit_congestion_control() so
that when cc algorithm is changed, ca_priv data is cleared out as well.
We should still zero out ca_priv data even in TCP_CLOSE state because
user could call connect() on AF_UNSPEC to disconnect the socket and
leave it in TCP_CLOSE state and later call setsockopt() to switch cc
algorithm on this socket.

Fixes: 2b0a8c9 ("tcp: add CDG congestion control")
Reported-by: Andrey Konovalov  <andreyknvl@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.

This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.

skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.

Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) MLX5 bug fixes from Saeed Mahameed et al:
     - released wrong resources when firmware timeout happens
     - fix wrong check for encapsulation size limits
     - UAR memory leak
     - ETHTOOL_GRXCLSRLALL failed to fill in info->data

 2) Don't cache l3mdev on mis-matches local route, causes net devices to
    leak refs. From Robert Shearman.

 3) Handle fragmented SKBs properly in macsec driver, the problem is
    that we were mis-sizing the sgvec table. From Jason A. Donenfeld.

 4) We cannot have checksum offload enabled for inner UDP tunneled
    packet during IPSEC, from Ansis Atteka.

 5) Fix double SKB free in ravb driver, from Dan Carpenter.

 6) Fix CPU port handling in b53 DSA driver, from Florian Dainelli.

 7) Don't use on-stack buffers for usb_control_msg() in CAN usb driver,
    from Maksim Salau.

 8) Fix device leak in macvlan driver, from Herbert Xu. We have to purge
    the broadcast queue properly on port destroy.

 9) Fix tx ring entry limit on EF10 devices in sfc driver. From Bert
    Kenward.

10) Fix memory leaks in team driver, from Pan Bian.

11) Don't setup ipv6_stub before it can be actually used, from Paolo
    Abeni.

12) Fix tipc socket flow control accounting, from Parthasarathy
    Bhuvaragan.

13) Fix crash on module unload in hso driver, from Andreas Kemnade.

14) Fix purging of bridge multicast entries, the problem is that if we
    don't defer it to ndo_uninit it's possible for new entries to get
    added after we purge. Fix from Xin Long.

15) Don't return garbage for PACKET_HDRLEN getsockopt, from Alexander
    Potapenko.

16) Fix autoneg stall properly in PHY layer, and revert micrel driver
    change that was papering over it. From Alexander Kochetkov.

17) Don't dereference an ipv4 route as an ipv6 one in the ip6_tunnnel
    code, from Cong Wang.

18) Clear out the congestion control private of the TCP socket in all of
    the right places, from Wei Wang.

19) rawv6_ioctl measures SKB length incorrectly, fix from Jamie
    Bainbridge.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  ipv6: check raw payload size correctly in ioctl
  tcp: memset ca_priv data to 0 properly
  ipv6: check skb->protocol before lookup for nexthop
  net: core: Prevent from dereferencing null pointer when releasing SKB
  macsec: dynamically allocate space for sglist
  Revert "phy: micrel: Disable auto negotiation on startup"
  net: phy: fix auto-negotiation stall due to unavailable interrupt
  net/packet: check length in getsockopt() called with PACKET_HDRLEN
  net: ipv6: regenerate host route if moved to gc list
  bridge: move bridge multicast cleanup to ndo_uninit
  ipv6: fix source routing
  qed: Fix error in the dcbx app meta data initialization.
  netvsc: fix calculation of available send sections
  net: hso: fix module unloading
  tipc: fix socket flow control accounting error at tipc_recv_stream
  tipc: fix socket flow control accounting error at tipc_send_stream
  ipv6: move stub initialization after ipv6 setup completion
  team: fix memory leaks
  sfc: tx ring can only have 2048 entries for all EF10 NICs
  macvlan: Fix device ref leak when purging bc_queue
  ...

With the new statx() syscall, the following both allow the attributes of
the file attached to a file descriptor to be retrieved:

	statx(dfd, NULL, 0, ...);

and:

	statx(dfd, "", AT_EMPTY_PATH, ...);

Change the code to reject the first option, though this means copying
the path and engaging pathwalk for the fstat() equivalent.  dfd can be a
non-directory provided path is "".

[ The timing of this isn't wonderful, but applying this now before we
  have statx() in any released kernel, before anybody starts using the
  NULL special case.    - Linus ]

Fixes: a528d35 ("statx: Add a system call to make enhanced file info available")
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Sandeen <sandeen@sandeen.net>
cc: fstests@vger.kernel.org
cc: linux-api@vger.kernel.org
cc: linux-man@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sparc fixes from David Miller:
 "I didn't want the release to go out without the statx system call
  properly hooked up"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Update syscall tables.
  sparc64: Fill in rest of HAVE_REGS_AND_STACK_ACCESS_API