| 1 | /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| 2 | /* Copyright (C) 2021 ROHM Semiconductors */ |
| 3 | |
| 4 | #ifndef __LINUX_MFD_BD957X_H__ |
| 5 | #define __LINUX_MFD_BD957X_H__ |
| 6 | |
| 7 | enum { |
| 8 | BD957X_VD50, |
| 9 | BD957X_VD18, |
| 10 | BD957X_VDDDR, |
| 11 | BD957X_VD10, |
| 12 | BD957X_VOUTL1, |
| 13 | BD957X_VOUTS1, |
| 14 | }; |
| 15 | |
| 16 | /* |
| 17 | * The BD9576 has own IRQ 'blocks' for: |
| 18 | * - I2C/thermal, |
| 19 | * - Over voltage protection |
| 20 | * - Short-circuit protection |
| 21 | * - Over current protection |
| 22 | * - Over voltage detection |
| 23 | * - Under voltage detection |
| 24 | * - Under voltage protection |
| 25 | * - 'system interrupt'. |
| 26 | * |
| 27 | * Each of the blocks have a status register giving more accurate IRQ source |
| 28 | * information - for example which of the regulators have over-voltage. |
| 29 | * |
| 30 | * On top of this, there is "main IRQ" status register where each bit indicates |
| 31 | * which of sub-blocks have active IRQs. Fine. That would fit regmap-irq main |
| 32 | * status handling. Except that: |
| 33 | * - Only some sub-IRQs can be masked. |
| 34 | * - The IRQ informs us about fault-condition, not when fault state changes. |
| 35 | * The IRQ line it is kept asserted until the detected condition is acked |
| 36 | * AND cleared in HW. This is annoying for IRQs like the one informing high |
| 37 | * temperature because if IRQ is not disabled it keeps the CPU in IRQ |
| 38 | * handling loop. |
| 39 | * |
| 40 | * For now we do just use the main-IRQ register as source for our IRQ |
| 41 | * information and bind the regmap-irq to this. We leave fine-grained sub-IRQ |
| 42 | * register handling to handlers in sub-devices. The regulator driver shall |
| 43 | * read which regulators are source for problem - or if the detected error is |
| 44 | * regulator temperature error. The sub-drivers do also handle masking of "sub- |
| 45 | * IRQs" if this is supported/needed. |
| 46 | * |
| 47 | * To overcome the problem with HW keeping IRQ asserted we do call |
| 48 | * disable_irq_nosync() from sub-device handler and add a delayed work to |
| 49 | * re-enable IRQ roughly 1 second later. This should keep our CPU out of |
| 50 | * busy-loop. |
| 51 | */ |
| 52 | #define IRQS_SILENT_MS 1000 |
| 53 | |
| 54 | enum { |
| 55 | BD9576_INT_THERM, |
| 56 | BD9576_INT_OVP, |
| 57 | BD9576_INT_SCP, |
| 58 | BD9576_INT_OCP, |
| 59 | BD9576_INT_OVD, |
| 60 | BD9576_INT_UVD, |
| 61 | BD9576_INT_UVP, |
| 62 | BD9576_INT_SYS, |
| 63 | }; |
| 64 | |
| 65 | #define BD957X_REG_SMRB_ASSERT 0x15 |
| 66 | #define BD957X_REG_PMIC_INTERNAL_STAT 0x20 |
| 67 | #define BD957X_REG_INT_THERM_STAT 0x23 |
| 68 | #define BD957X_REG_INT_THERM_MASK 0x24 |
| 69 | #define BD957X_REG_INT_OVP_STAT 0x25 |
| 70 | #define BD957X_REG_INT_SCP_STAT 0x26 |
| 71 | #define BD957X_REG_INT_OCP_STAT 0x27 |
| 72 | #define BD957X_REG_INT_OVD_STAT 0x28 |
| 73 | #define BD957X_REG_INT_UVD_STAT 0x29 |
| 74 | #define BD957X_REG_INT_UVP_STAT 0x2a |
| 75 | #define BD957X_REG_INT_SYS_STAT 0x2b |
| 76 | #define BD957X_REG_INT_SYS_MASK 0x2c |
| 77 | #define BD957X_REG_INT_MAIN_STAT 0x30 |
| 78 | #define BD957X_REG_INT_MAIN_MASK 0x31 |
| 79 | |
| 80 | #define UVD_IRQ_VALID_MASK 0x6F |
| 81 | #define OVD_IRQ_VALID_MASK 0x2F |
| 82 | |
| 83 | #define BD957X_MASK_INT_MAIN_THERM BIT(0) |
| 84 | #define BD957X_MASK_INT_MAIN_OVP BIT(1) |
| 85 | #define BD957X_MASK_INT_MAIN_SCP BIT(2) |
| 86 | #define BD957X_MASK_INT_MAIN_OCP BIT(3) |
| 87 | #define BD957X_MASK_INT_MAIN_OVD BIT(4) |
| 88 | #define BD957X_MASK_INT_MAIN_UVD BIT(5) |
| 89 | #define BD957X_MASK_INT_MAIN_UVP BIT(6) |
| 90 | #define BD957X_MASK_INT_MAIN_SYS BIT(7) |
| 91 | #define BD957X_MASK_INT_ALL 0xff |
| 92 | |
| 93 | #define BD957X_REG_WDT_CONF 0x16 |
| 94 | |
| 95 | #define BD957X_REG_POW_TRIGGER1 0x41 |
| 96 | #define BD957X_REG_POW_TRIGGER2 0x42 |
| 97 | #define BD957X_REG_POW_TRIGGER3 0x43 |
| 98 | #define BD957X_REG_POW_TRIGGER4 0x44 |
| 99 | #define BD957X_REG_POW_TRIGGERL1 0x45 |
| 100 | #define BD957X_REG_POW_TRIGGERS1 0x46 |
| 101 | |
| 102 | #define BD957X_REGULATOR_EN_MASK 0xff |
| 103 | #define BD957X_REGULATOR_DIS_VAL 0xff |
| 104 | |
| 105 | #define BD957X_VSEL_REG_MASK 0xff |
| 106 | |
| 107 | #define BD957X_MASK_VOUT1_TUNE 0x87 |
| 108 | #define BD957X_MASK_VOUT2_TUNE 0x87 |
| 109 | #define BD957X_MASK_VOUT3_TUNE 0x1f |
| 110 | #define BD957X_MASK_VOUT4_TUNE 0x1f |
| 111 | #define BD957X_MASK_VOUTL1_TUNE 0x87 |
| 112 | |
| 113 | #define BD957X_REG_VOUT1_TUNE 0x50 |
| 114 | #define BD957X_REG_VOUT2_TUNE 0x53 |
| 115 | #define BD957X_REG_VOUT3_TUNE 0x56 |
| 116 | #define BD957X_REG_VOUT4_TUNE 0x59 |
| 117 | #define BD957X_REG_VOUTL1_TUNE 0x5c |
| 118 | |
| 119 | #define BD9576_REG_VOUT1_OVD 0x51 |
| 120 | #define BD9576_REG_VOUT1_UVD 0x52 |
| 121 | #define BD9576_REG_VOUT2_OVD 0x54 |
| 122 | #define BD9576_REG_VOUT2_UVD 0x55 |
| 123 | #define BD9576_REG_VOUT3_OVD 0x57 |
| 124 | #define BD9576_REG_VOUT3_UVD 0x58 |
| 125 | #define BD9576_REG_VOUT4_OVD 0x5a |
| 126 | #define BD9576_REG_VOUT4_UVD 0x5b |
| 127 | #define BD9576_REG_VOUTL1_OVD 0x5d |
| 128 | #define BD9576_REG_VOUTL1_UVD 0x5e |
| 129 | |
| 130 | #define BD9576_MASK_XVD 0x7f |
| 131 | |
| 132 | #define BD9576_REG_VOUT1S_OCW 0x5f |
| 133 | #define BD9576_REG_VOUT1S_OCP 0x60 |
| 134 | |
| 135 | #define BD9576_MASK_VOUT1S_OCW 0x3f |
| 136 | #define BD9576_MASK_VOUT1S_OCP 0x3f |
| 137 | |
| 138 | #define BD957X_MAX_REGISTER 0x61 |
| 139 | |
| 140 | #endif |
| 141 | |