| 1 | // SPDX-License-Identifier: GPL-2.0-or-later |
| 2 | /* |
| 3 | * twl-regulator.c -- support regulators in twl4030/twl6030 family chips |
| 4 | * |
| 5 | * Copyright (C) 2008 David Brownell |
| 6 | */ |
| 7 | |
| 8 | #include <linux/module.h> |
| 9 | #include <linux/string.h> |
| 10 | #include <linux/slab.h> |
| 11 | #include <linux/init.h> |
| 12 | #include <linux/err.h> |
| 13 | #include <linux/platform_device.h> |
| 14 | #include <linux/of.h> |
| 15 | #include <linux/regulator/driver.h> |
| 16 | #include <linux/regulator/machine.h> |
| 17 | #include <linux/regulator/of_regulator.h> |
| 18 | #include <linux/mfd/twl.h> |
| 19 | #include <linux/delay.h> |
| 20 | |
| 21 | /* |
| 22 | * The TWL4030/TW5030/TPS659x0 family chips include power management, a |
| 23 | * USB OTG transceiver, an RTC, ADC, PWM, and lots more. Some versions |
| 24 | * include an audio codec, battery charger, and more voltage regulators. |
| 25 | * These chips are often used in OMAP-based systems. |
| 26 | * |
| 27 | * This driver implements software-based resource control for various |
| 28 | * voltage regulators. This is usually augmented with state machine |
| 29 | * based control. |
| 30 | */ |
| 31 | |
| 32 | struct twlreg_info { |
| 33 | /* start of regulator's PM_RECEIVER control register bank */ |
| 34 | u8 base; |
| 35 | |
| 36 | /* twl resource ID, for resource control state machine */ |
| 37 | u8 id; |
| 38 | |
| 39 | /* voltage in mV = table[VSEL]; table_len must be a power-of-two */ |
| 40 | u8 table_len; |
| 41 | const u16 *table; |
| 42 | |
| 43 | /* State REMAP default configuration */ |
| 44 | u8 remap; |
| 45 | |
| 46 | /* used by regulator core */ |
| 47 | struct regulator_desc desc; |
| 48 | |
| 49 | /* chip specific features */ |
| 50 | unsigned long features; |
| 51 | |
| 52 | /* data passed from board for external get/set voltage */ |
| 53 | void *data; |
| 54 | }; |
| 55 | |
| 56 | |
| 57 | /* LDO control registers ... offset is from the base of its register bank. |
| 58 | * The first three registers of all power resource banks help hardware to |
| 59 | * manage the various resource groups. |
| 60 | */ |
| 61 | /* Common offset in TWL4030/6030 */ |
| 62 | #define VREG_GRP 0 |
| 63 | /* TWL4030 register offsets */ |
| 64 | #define VREG_TYPE 1 |
| 65 | #define VREG_REMAP 2 |
| 66 | #define VREG_DEDICATED 3 /* LDO control */ |
| 67 | #define VREG_VOLTAGE_SMPS_4030 9 |
| 68 | /* TWL6030 register offsets */ |
| 69 | #define VREG_TRANS 1 |
| 70 | #define VREG_STATE 2 |
| 71 | #define VREG_VOLTAGE 3 |
| 72 | #define VREG_VOLTAGE_SMPS 4 |
| 73 | |
| 74 | static inline int |
| 75 | twlreg_read(struct twlreg_info *info, unsigned slave_subgp, unsigned offset) |
| 76 | { |
| 77 | u8 value; |
| 78 | int status; |
| 79 | |
| 80 | status = twl_i2c_read_u8(mod_no: slave_subgp, |
| 81 | val: &value, reg: info->base + offset); |
| 82 | return (status < 0) ? status : value; |
| 83 | } |
| 84 | |
| 85 | static inline int |
| 86 | twlreg_write(struct twlreg_info *info, unsigned slave_subgp, unsigned offset, |
| 87 | u8 value) |
| 88 | { |
| 89 | return twl_i2c_write_u8(mod_no: slave_subgp, |
| 90 | val: value, reg: info->base + offset); |
| 91 | } |
| 92 | |
| 93 | /*----------------------------------------------------------------------*/ |
| 94 | |
| 95 | /* generic power resource operations, which work on all regulators */ |
| 96 | |
| 97 | static int twlreg_grp(struct regulator_dev *rdev) |
| 98 | { |
| 99 | return twlreg_read(info: rdev_get_drvdata(rdev), slave_subgp: TWL_MODULE_PM_RECEIVER, |
| 100 | VREG_GRP); |
| 101 | } |
| 102 | |
| 103 | /* |
| 104 | * Enable/disable regulators by joining/leaving the P1 (processor) group. |
| 105 | * We assume nobody else is updating the DEV_GRP registers. |
| 106 | */ |
| 107 | /* definition for 4030 family */ |
| 108 | #define P3_GRP_4030 BIT(7) /* "peripherals" */ |
| 109 | #define P2_GRP_4030 BIT(6) /* secondary processor, modem, etc */ |
| 110 | #define P1_GRP_4030 BIT(5) /* CPU/Linux */ |
| 111 | /* definition for 6030 family */ |
| 112 | #define P3_GRP_6030 BIT(2) /* secondary processor, modem, etc */ |
| 113 | #define P2_GRP_6030 BIT(1) /* "peripherals" */ |
| 114 | #define P1_GRP_6030 BIT(0) /* CPU/Linux */ |
| 115 | |
| 116 | static int twl4030reg_is_enabled(struct regulator_dev *rdev) |
| 117 | { |
| 118 | int state = twlreg_grp(rdev); |
| 119 | |
| 120 | if (state < 0) |
| 121 | return state; |
| 122 | |
| 123 | return state & P1_GRP_4030; |
| 124 | } |
| 125 | |
| 126 | #define PB_I2C_BUSY BIT(0) |
| 127 | #define PB_I2C_BWEN BIT(1) |
| 128 | |
| 129 | /* Wait until buffer empty/ready to send a word on power bus. */ |
| 130 | static int twl4030_wait_pb_ready(void) |
| 131 | { |
| 132 | |
| 133 | int ret; |
| 134 | int timeout = 10; |
| 135 | u8 val; |
| 136 | |
| 137 | do { |
| 138 | ret = twl_i2c_read_u8(mod_no: TWL_MODULE_PM_MASTER, val: &val, |
| 139 | TWL4030_PM_MASTER_PB_CFG); |
| 140 | if (ret < 0) |
| 141 | return ret; |
| 142 | |
| 143 | if (!(val & PB_I2C_BUSY)) |
| 144 | return 0; |
| 145 | |
| 146 | mdelay(1); |
| 147 | timeout--; |
| 148 | } while (timeout); |
| 149 | |
| 150 | return -ETIMEDOUT; |
| 151 | } |
| 152 | |
| 153 | /* Send a word over the powerbus */ |
| 154 | static int twl4030_send_pb_msg(unsigned msg) |
| 155 | { |
| 156 | u8 val; |
| 157 | int ret; |
| 158 | |
| 159 | /* save powerbus configuration */ |
| 160 | ret = twl_i2c_read_u8(mod_no: TWL_MODULE_PM_MASTER, val: &val, |
| 161 | TWL4030_PM_MASTER_PB_CFG); |
| 162 | if (ret < 0) |
| 163 | return ret; |
| 164 | |
| 165 | /* Enable i2c access to powerbus */ |
| 166 | ret = twl_i2c_write_u8(mod_no: TWL_MODULE_PM_MASTER, val: val | PB_I2C_BWEN, |
| 167 | TWL4030_PM_MASTER_PB_CFG); |
| 168 | if (ret < 0) |
| 169 | return ret; |
| 170 | |
| 171 | ret = twl4030_wait_pb_ready(); |
| 172 | if (ret < 0) |
| 173 | return ret; |
| 174 | |
| 175 | ret = twl_i2c_write_u8(mod_no: TWL_MODULE_PM_MASTER, val: msg >> 8, |
| 176 | TWL4030_PM_MASTER_PB_WORD_MSB); |
| 177 | if (ret < 0) |
| 178 | return ret; |
| 179 | |
| 180 | ret = twl_i2c_write_u8(mod_no: TWL_MODULE_PM_MASTER, val: msg & 0xff, |
| 181 | TWL4030_PM_MASTER_PB_WORD_LSB); |
| 182 | if (ret < 0) |
| 183 | return ret; |
| 184 | |
| 185 | ret = twl4030_wait_pb_ready(); |
| 186 | if (ret < 0) |
| 187 | return ret; |
| 188 | |
| 189 | /* Restore powerbus configuration */ |
| 190 | return twl_i2c_write_u8(mod_no: TWL_MODULE_PM_MASTER, val, |
| 191 | TWL4030_PM_MASTER_PB_CFG); |
| 192 | } |
| 193 | |
| 194 | static int twl4030reg_enable(struct regulator_dev *rdev) |
| 195 | { |
| 196 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 197 | int grp; |
| 198 | |
| 199 | grp = twlreg_grp(rdev); |
| 200 | if (grp < 0) |
| 201 | return grp; |
| 202 | |
| 203 | grp |= P1_GRP_4030; |
| 204 | |
| 205 | return twlreg_write(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_GRP, value: grp); |
| 206 | } |
| 207 | |
| 208 | static int twl4030reg_disable(struct regulator_dev *rdev) |
| 209 | { |
| 210 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 211 | int grp; |
| 212 | |
| 213 | grp = twlreg_grp(rdev); |
| 214 | if (grp < 0) |
| 215 | return grp; |
| 216 | |
| 217 | grp &= ~(P1_GRP_4030 | P2_GRP_4030 | P3_GRP_4030); |
| 218 | |
| 219 | return twlreg_write(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_GRP, value: grp); |
| 220 | } |
| 221 | |
| 222 | static int twl4030reg_get_status(struct regulator_dev *rdev) |
| 223 | { |
| 224 | int state = twlreg_grp(rdev); |
| 225 | |
| 226 | if (state < 0) |
| 227 | return state; |
| 228 | state &= 0x0f; |
| 229 | |
| 230 | /* assume state != WARM_RESET; we'd not be running... */ |
| 231 | if (!state) |
| 232 | return REGULATOR_STATUS_OFF; |
| 233 | return (state & BIT(3)) |
| 234 | ? REGULATOR_STATUS_NORMAL |
| 235 | : REGULATOR_STATUS_STANDBY; |
| 236 | } |
| 237 | |
| 238 | static int twl4030reg_set_mode(struct regulator_dev *rdev, unsigned mode) |
| 239 | { |
| 240 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 241 | unsigned message; |
| 242 | |
| 243 | /* We can only set the mode through state machine commands... */ |
| 244 | switch (mode) { |
| 245 | case REGULATOR_MODE_NORMAL: |
| 246 | message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_ACTIVE); |
| 247 | break; |
| 248 | case REGULATOR_MODE_STANDBY: |
| 249 | message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_SLEEP); |
| 250 | break; |
| 251 | default: |
| 252 | return -EINVAL; |
| 253 | } |
| 254 | |
| 255 | return twl4030_send_pb_msg(msg: message); |
| 256 | } |
| 257 | |
| 258 | static inline unsigned int twl4030reg_map_mode(unsigned int mode) |
| 259 | { |
| 260 | switch (mode) { |
| 261 | case RES_STATE_ACTIVE: |
| 262 | return REGULATOR_MODE_NORMAL; |
| 263 | case RES_STATE_SLEEP: |
| 264 | return REGULATOR_MODE_STANDBY; |
| 265 | default: |
| 266 | return REGULATOR_MODE_INVALID; |
| 267 | } |
| 268 | } |
| 269 | |
| 270 | /*----------------------------------------------------------------------*/ |
| 271 | |
| 272 | /* |
| 273 | * Support for adjustable-voltage LDOs uses a four bit (or less) voltage |
| 274 | * select field in its control register. We use tables indexed by VSEL |
| 275 | * to record voltages in milliVolts. (Accuracy is about three percent.) |
| 276 | * |
| 277 | * Note that VSEL values for VAUX2 changed in twl5030 and newer silicon; |
| 278 | * currently handled by listing two slightly different VAUX2 regulators, |
| 279 | * only one of which will be configured. |
| 280 | * |
| 281 | * VSEL values documented as "TI cannot support these values" are flagged |
| 282 | * in these tables as UNSUP() values; we normally won't assign them. |
| 283 | * |
| 284 | * VAUX3 at 3V is incorrectly listed in some TI manuals as unsupported. |
| 285 | * TI are revising the twl5030/tps659x0 specs to support that 3.0V setting. |
| 286 | */ |
| 287 | #define UNSUP_MASK 0x8000 |
| 288 | |
| 289 | #define UNSUP(x) (UNSUP_MASK | (x)) |
| 290 | #define IS_UNSUP(info, x) \ |
| 291 | ((UNSUP_MASK & (x)) && \ |
| 292 | !((info)->features & TWL4030_ALLOW_UNSUPPORTED)) |
| 293 | #define LDO_MV(x) (~UNSUP_MASK & (x)) |
| 294 | |
| 295 | |
| 296 | static const u16 VAUX1_VSEL_table[] = { |
| 297 | UNSUP(1500), UNSUP(1800), 2500, 2800, |
| 298 | 3000, 3000, 3000, 3000, |
| 299 | }; |
| 300 | static const u16 VAUX2_4030_VSEL_table[] = { |
| 301 | UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300, |
| 302 | 1500, 1800, UNSUP(1850), 2500, |
| 303 | UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), |
| 304 | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), |
| 305 | }; |
| 306 | static const u16 VAUX2_VSEL_table[] = { |
| 307 | 1700, 1700, 1900, 1300, |
| 308 | 1500, 1800, 2000, 2500, |
| 309 | 2100, 2800, 2200, 2300, |
| 310 | 2400, 2400, 2400, 2400, |
| 311 | }; |
| 312 | static const u16 VAUX3_VSEL_table[] = { |
| 313 | 1500, 1800, 2500, 2800, |
| 314 | 3000, 3000, 3000, 3000, |
| 315 | }; |
| 316 | static const u16 VAUX4_VSEL_table[] = { |
| 317 | 700, 1000, 1200, UNSUP(1300), |
| 318 | 1500, 1800, UNSUP(1850), 2500, |
| 319 | UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), |
| 320 | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), |
| 321 | }; |
| 322 | static const u16 VMMC1_VSEL_table[] = { |
| 323 | 1850, 2850, 3000, 3150, |
| 324 | }; |
| 325 | static const u16 VMMC2_VSEL_table[] = { |
| 326 | UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300), |
| 327 | UNSUP(1500), UNSUP(1800), 1850, UNSUP(2500), |
| 328 | 2600, 2800, 2850, 3000, |
| 329 | 3150, 3150, 3150, 3150, |
| 330 | }; |
| 331 | static const u16 VPLL1_VSEL_table[] = { |
| 332 | 1000, 1200, 1300, 1800, |
| 333 | UNSUP(2800), UNSUP(3000), UNSUP(3000), UNSUP(3000), |
| 334 | }; |
| 335 | static const u16 VPLL2_VSEL_table[] = { |
| 336 | 700, 1000, 1200, 1300, |
| 337 | UNSUP(1500), 1800, UNSUP(1850), UNSUP(2500), |
| 338 | UNSUP(2600), UNSUP(2800), UNSUP(2850), UNSUP(3000), |
| 339 | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), |
| 340 | }; |
| 341 | static const u16 VSIM_VSEL_table[] = { |
| 342 | UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800, |
| 343 | 2800, 3000, 3000, 3000, |
| 344 | }; |
| 345 | static const u16 VDAC_VSEL_table[] = { |
| 346 | 1200, 1300, 1800, 1800, |
| 347 | }; |
| 348 | static const u16 VIO_VSEL_table[] = { |
| 349 | 1800, 1850, |
| 350 | }; |
| 351 | static const u16 VINTANA2_VSEL_table[] = { |
| 352 | 2500, 2750, |
| 353 | }; |
| 354 | |
| 355 | /* 600mV to 1450mV in 12.5 mV steps */ |
| 356 | static const struct linear_range VDD1_ranges[] = { |
| 357 | REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500) |
| 358 | }; |
| 359 | |
| 360 | /* 600mV to 1450mV in 12.5 mV steps, everything above = 1500mV */ |
| 361 | static const struct linear_range VDD2_ranges[] = { |
| 362 | REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500), |
| 363 | REGULATOR_LINEAR_RANGE(1500000, 69, 69, 12500) |
| 364 | }; |
| 365 | |
| 366 | static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) |
| 367 | { |
| 368 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 369 | int mV = info->table[index]; |
| 370 | |
| 371 | return IS_UNSUP(info, mV) ? 0 : (LDO_MV(mV) * 1000); |
| 372 | } |
| 373 | |
| 374 | static int |
| 375 | twl4030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector) |
| 376 | { |
| 377 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 378 | |
| 379 | return twlreg_write(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE, |
| 380 | value: selector); |
| 381 | } |
| 382 | |
| 383 | static int twl4030ldo_get_voltage_sel(struct regulator_dev *rdev) |
| 384 | { |
| 385 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 386 | int vsel = twlreg_read(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE); |
| 387 | |
| 388 | if (vsel < 0) |
| 389 | return vsel; |
| 390 | |
| 391 | vsel &= info->table_len - 1; |
| 392 | return vsel; |
| 393 | } |
| 394 | |
| 395 | static const struct regulator_ops twl4030ldo_ops = { |
| 396 | .list_voltage = twl4030ldo_list_voltage, |
| 397 | |
| 398 | .set_voltage_sel = twl4030ldo_set_voltage_sel, |
| 399 | .get_voltage_sel = twl4030ldo_get_voltage_sel, |
| 400 | |
| 401 | .enable = twl4030reg_enable, |
| 402 | .disable = twl4030reg_disable, |
| 403 | .is_enabled = twl4030reg_is_enabled, |
| 404 | |
| 405 | .set_mode = twl4030reg_set_mode, |
| 406 | |
| 407 | .get_status = twl4030reg_get_status, |
| 408 | }; |
| 409 | |
| 410 | static int |
| 411 | twl4030smps_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV, |
| 412 | unsigned *selector) |
| 413 | { |
| 414 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 415 | int vsel = DIV_ROUND_UP(min_uV - 600000, 12500); |
| 416 | |
| 417 | twlreg_write(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS_4030, value: vsel); |
| 418 | |
| 419 | return 0; |
| 420 | } |
| 421 | |
| 422 | static int twl4030smps_get_voltage(struct regulator_dev *rdev) |
| 423 | { |
| 424 | struct twlreg_info *info = rdev_get_drvdata(rdev); |
| 425 | int vsel; |
| 426 | |
| 427 | vsel = twlreg_read(info, slave_subgp: TWL_MODULE_PM_RECEIVER, |
| 428 | VREG_VOLTAGE_SMPS_4030); |
| 429 | |
| 430 | return vsel * 12500 + 600000; |
| 431 | } |
| 432 | |
| 433 | static const struct regulator_ops twl4030smps_ops = { |
| 434 | .list_voltage = regulator_list_voltage_linear_range, |
| 435 | |
| 436 | .set_voltage = twl4030smps_set_voltage, |
| 437 | .get_voltage = twl4030smps_get_voltage, |
| 438 | }; |
| 439 | |
| 440 | /*----------------------------------------------------------------------*/ |
| 441 | |
| 442 | static const struct regulator_ops twl4030fixed_ops = { |
| 443 | .list_voltage = regulator_list_voltage_linear, |
| 444 | |
| 445 | .enable = twl4030reg_enable, |
| 446 | .disable = twl4030reg_disable, |
| 447 | .is_enabled = twl4030reg_is_enabled, |
| 448 | |
| 449 | .set_mode = twl4030reg_set_mode, |
| 450 | |
| 451 | .get_status = twl4030reg_get_status, |
| 452 | }; |
| 453 | |
| 454 | /*----------------------------------------------------------------------*/ |
| 455 | |
| 456 | #define TWL4030_ADJUSTABLE_LDO(label, offset, num, turnon_delay, remap_conf) \ |
| 457 | static const struct twlreg_info TWL4030_INFO_##label = { \ |
| 458 | .base = offset, \ |
| 459 | .id = num, \ |
| 460 | .table_len = ARRAY_SIZE(label##_VSEL_table), \ |
| 461 | .table = label##_VSEL_table, \ |
| 462 | .remap = remap_conf, \ |
| 463 | .desc = { \ |
| 464 | .name = #label, \ |
| 465 | .id = TWL4030_REG_##label, \ |
| 466 | .n_voltages = ARRAY_SIZE(label##_VSEL_table), \ |
| 467 | .ops = &twl4030ldo_ops, \ |
| 468 | .type = REGULATOR_VOLTAGE, \ |
| 469 | .owner = THIS_MODULE, \ |
| 470 | .enable_time = turnon_delay, \ |
| 471 | .of_map_mode = twl4030reg_map_mode, \ |
| 472 | }, \ |
| 473 | } |
| 474 | |
| 475 | #define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf, \ |
| 476 | n_volt) \ |
| 477 | static const struct twlreg_info TWL4030_INFO_##label = { \ |
| 478 | .base = offset, \ |
| 479 | .id = num, \ |
| 480 | .remap = remap_conf, \ |
| 481 | .desc = { \ |
| 482 | .name = #label, \ |
| 483 | .id = TWL4030_REG_##label, \ |
| 484 | .ops = &twl4030smps_ops, \ |
| 485 | .type = REGULATOR_VOLTAGE, \ |
| 486 | .owner = THIS_MODULE, \ |
| 487 | .enable_time = turnon_delay, \ |
| 488 | .of_map_mode = twl4030reg_map_mode, \ |
| 489 | .n_voltages = n_volt, \ |
| 490 | .n_linear_ranges = ARRAY_SIZE(label ## _ranges), \ |
| 491 | .linear_ranges = label ## _ranges, \ |
| 492 | }, \ |
| 493 | } |
| 494 | |
| 495 | #define TWL4030_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \ |
| 496 | remap_conf) \ |
| 497 | static const struct twlreg_info TWLFIXED_INFO_##label = { \ |
| 498 | .base = offset, \ |
| 499 | .id = num, \ |
| 500 | .remap = remap_conf, \ |
| 501 | .desc = { \ |
| 502 | .name = #label, \ |
| 503 | .id = TWL4030##_REG_##label, \ |
| 504 | .n_voltages = 1, \ |
| 505 | .ops = &twl4030fixed_ops, \ |
| 506 | .type = REGULATOR_VOLTAGE, \ |
| 507 | .owner = THIS_MODULE, \ |
| 508 | .min_uV = mVolts * 1000, \ |
| 509 | .enable_time = turnon_delay, \ |
| 510 | .of_map_mode = twl4030reg_map_mode, \ |
| 511 | }, \ |
| 512 | } |
| 513 | |
| 514 | /* |
| 515 | * We list regulators here if systems need some level of |
| 516 | * software control over them after boot. |
| 517 | */ |
| 518 | TWL4030_ADJUSTABLE_LDO(VAUX1, 0x17, 1, 100, 0x08); |
| 519 | TWL4030_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2, 100, 0x08); |
| 520 | TWL4030_ADJUSTABLE_LDO(VAUX2, 0x1b, 2, 100, 0x08); |
| 521 | TWL4030_ADJUSTABLE_LDO(VAUX3, 0x1f, 3, 100, 0x08); |
| 522 | TWL4030_ADJUSTABLE_LDO(VAUX4, 0x23, 4, 100, 0x08); |
| 523 | TWL4030_ADJUSTABLE_LDO(VMMC1, 0x27, 5, 100, 0x08); |
| 524 | TWL4030_ADJUSTABLE_LDO(VMMC2, 0x2b, 6, 100, 0x08); |
| 525 | TWL4030_ADJUSTABLE_LDO(VPLL1, 0x2f, 7, 100, 0x00); |
| 526 | TWL4030_ADJUSTABLE_LDO(VPLL2, 0x33, 8, 100, 0x08); |
| 527 | TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); |
| 528 | TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); |
| 529 | TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); |
| 530 | TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); |
| 531 | TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08, 68); |
| 532 | TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08, 69); |
| 533 | /* VUSBCP is managed *only* by the USB subchip */ |
| 534 | TWL4030_FIXED_LDO(VINTANA1, 0x3f, 1500, 11, 100, 0x08); |
| 535 | TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08); |
| 536 | TWL4030_FIXED_LDO(VUSB1V5, 0x71, 1500, 17, 100, 0x08); |
| 537 | TWL4030_FIXED_LDO(VUSB1V8, 0x74, 1800, 18, 100, 0x08); |
| 538 | TWL4030_FIXED_LDO(VUSB3V1, 0x77, 3100, 19, 150, 0x08); |
| 539 | |
| 540 | #define TWL_OF_MATCH(comp, family, label) \ |
| 541 | { \ |
| 542 | .compatible = comp, \ |
| 543 | .data = &family##_INFO_##label, \ |
| 544 | } |
| 545 | |
| 546 | #define TWL4030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL4030, label) |
| 547 | #define TWL6030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6030, label) |
| 548 | #define TWL6032_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6032, label) |
| 549 | #define TWLFIXED_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLFIXED, label) |
| 550 | #define TWLSMPS_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLSMPS, label) |
| 551 | |
| 552 | static const struct of_device_id twl_of_match[] = { |
| 553 | TWL4030_OF_MATCH("ti,twl4030-vaux1" , VAUX1), |
| 554 | TWL4030_OF_MATCH("ti,twl4030-vaux2" , VAUX2_4030), |
| 555 | TWL4030_OF_MATCH("ti,twl5030-vaux2" , VAUX2), |
| 556 | TWL4030_OF_MATCH("ti,twl4030-vaux3" , VAUX3), |
| 557 | TWL4030_OF_MATCH("ti,twl4030-vaux4" , VAUX4), |
| 558 | TWL4030_OF_MATCH("ti,twl4030-vmmc1" , VMMC1), |
| 559 | TWL4030_OF_MATCH("ti,twl4030-vmmc2" , VMMC2), |
| 560 | TWL4030_OF_MATCH("ti,twl4030-vpll1" , VPLL1), |
| 561 | TWL4030_OF_MATCH("ti,twl4030-vpll2" , VPLL2), |
| 562 | TWL4030_OF_MATCH("ti,twl4030-vsim" , VSIM), |
| 563 | TWL4030_OF_MATCH("ti,twl4030-vdac" , VDAC), |
| 564 | TWL4030_OF_MATCH("ti,twl4030-vintana2" , VINTANA2), |
| 565 | TWL4030_OF_MATCH("ti,twl4030-vio" , VIO), |
| 566 | TWL4030_OF_MATCH("ti,twl4030-vdd1" , VDD1), |
| 567 | TWL4030_OF_MATCH("ti,twl4030-vdd2" , VDD2), |
| 568 | TWLFIXED_OF_MATCH("ti,twl4030-vintana1" , VINTANA1), |
| 569 | TWLFIXED_OF_MATCH("ti,twl4030-vintdig" , VINTDIG), |
| 570 | TWLFIXED_OF_MATCH("ti,twl4030-vusb1v5" , VUSB1V5), |
| 571 | TWLFIXED_OF_MATCH("ti,twl4030-vusb1v8" , VUSB1V8), |
| 572 | TWLFIXED_OF_MATCH("ti,twl4030-vusb3v1" , VUSB3V1), |
| 573 | {}, |
| 574 | }; |
| 575 | MODULE_DEVICE_TABLE(of, twl_of_match); |
| 576 | |
| 577 | static int twlreg_probe(struct platform_device *pdev) |
| 578 | { |
| 579 | int id; |
| 580 | struct twlreg_info *info; |
| 581 | const struct twlreg_info *template; |
| 582 | struct regulator_init_data *initdata; |
| 583 | struct regulation_constraints *c; |
| 584 | struct regulator_dev *rdev; |
| 585 | struct regulator_config config = { }; |
| 586 | |
| 587 | template = of_device_get_match_data(dev: &pdev->dev); |
| 588 | if (!template) |
| 589 | return -ENODEV; |
| 590 | |
| 591 | id = template->desc.id; |
| 592 | initdata = of_get_regulator_init_data(dev: &pdev->dev, node: pdev->dev.of_node, |
| 593 | desc: &template->desc); |
| 594 | if (!initdata) |
| 595 | return -EINVAL; |
| 596 | |
| 597 | info = devm_kmemdup(dev: &pdev->dev, src: template, len: sizeof(*info), GFP_KERNEL); |
| 598 | if (!info) |
| 599 | return -ENOMEM; |
| 600 | |
| 601 | /* Constrain board-specific capabilities according to what |
| 602 | * this driver and the chip itself can actually do. |
| 603 | */ |
| 604 | c = &initdata->constraints; |
| 605 | c->valid_modes_mask &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY; |
| 606 | c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE |
| 607 | | REGULATOR_CHANGE_MODE |
| 608 | | REGULATOR_CHANGE_STATUS; |
| 609 | switch (id) { |
| 610 | case TWL4030_REG_VIO: |
| 611 | case TWL4030_REG_VDD1: |
| 612 | case TWL4030_REG_VDD2: |
| 613 | case TWL4030_REG_VPLL1: |
| 614 | case TWL4030_REG_VINTANA1: |
| 615 | case TWL4030_REG_VINTANA2: |
| 616 | case TWL4030_REG_VINTDIG: |
| 617 | c->always_on = true; |
| 618 | break; |
| 619 | default: |
| 620 | break; |
| 621 | } |
| 622 | |
| 623 | config.dev = &pdev->dev; |
| 624 | config.init_data = initdata; |
| 625 | config.driver_data = info; |
| 626 | config.of_node = pdev->dev.of_node; |
| 627 | |
| 628 | rdev = devm_regulator_register(dev: &pdev->dev, regulator_desc: &info->desc, config: &config); |
| 629 | if (IS_ERR(ptr: rdev)) { |
| 630 | dev_err(&pdev->dev, "can't register %s, %ld\n" , |
| 631 | info->desc.name, PTR_ERR(rdev)); |
| 632 | return PTR_ERR(ptr: rdev); |
| 633 | } |
| 634 | platform_set_drvdata(pdev, data: rdev); |
| 635 | |
| 636 | twlreg_write(info, slave_subgp: TWL_MODULE_PM_RECEIVER, VREG_REMAP, value: info->remap); |
| 637 | |
| 638 | /* NOTE: many regulators support short-circuit IRQs (presentable |
| 639 | * as REGULATOR_OVER_CURRENT notifications?) configured via: |
| 640 | * - SC_CONFIG |
| 641 | * - SC_DETECT1 (vintana2, vmmc1/2, vaux1/2/3/4) |
| 642 | * - SC_DETECT2 (vusb, vdac, vio, vdd1/2, vpll2) |
| 643 | * - IT_CONFIG |
| 644 | */ |
| 645 | |
| 646 | return 0; |
| 647 | } |
| 648 | |
| 649 | MODULE_ALIAS("platform:twl4030_reg" ); |
| 650 | |
| 651 | static struct platform_driver twlreg_driver = { |
| 652 | .probe = twlreg_probe, |
| 653 | /* NOTE: short name, to work around driver model truncation of |
| 654 | * "twl_regulator.12" (and friends) to "twl_regulator.1". |
| 655 | */ |
| 656 | .driver = { |
| 657 | .name = "twl4030_reg" , |
| 658 | .probe_type = PROBE_PREFER_ASYNCHRONOUS, |
| 659 | .of_match_table = of_match_ptr(twl_of_match), |
| 660 | }, |
| 661 | }; |
| 662 | |
| 663 | static int __init twlreg_init(void) |
| 664 | { |
| 665 | return platform_driver_register(&twlreg_driver); |
| 666 | } |
| 667 | subsys_initcall(twlreg_init); |
| 668 | |
| 669 | static void __exit twlreg_exit(void) |
| 670 | { |
| 671 | platform_driver_unregister(&twlreg_driver); |
| 672 | } |
| 673 | module_exit(twlreg_exit) |
| 674 | |
| 675 | MODULE_DESCRIPTION("TWL4030 regulator driver" ); |
| 676 | MODULE_LICENSE("GPL" ); |
| 677 | |