/*
 * Copyright 2017 NXP
 * All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#include "boards/flash_config.h"

#include "fsl_flexspi_nor_boot.h"


__attribute__((section(".boot_hdr.ivt")))
/*************************************
 *  IVT Data
 *************************************/
const ivt image_vector_table = {
    IVT_HEADER,                       /* IVT Header */
    IMAGE_ENTRY_ADDRESS,              /* Image Entry Function */
    IVT_RSVD,                         /* Reserved = 0 */
    (uint32_t)DCD_ADDRESS,            /* Address where DCD information is stored */
    (uint32_t)BOOT_DATA_ADDRESS,      /* Address where BOOT Data Structure is stored */
    (uint32_t)&image_vector_table,    /* Pointer to IVT Self (absolute address */
    (uint32_t)CSF_ADDRESS,            /* Address where CSF file is stored */
    IVT_RSVD                          /* Reserved = 0 */
};

__attribute__((section(".boot_hdr.boot_data")))
/*************************************
 *  Boot Data
 *************************************/
const BOOT_DATA_T boot_data = {
    FLASH_BASE,               /* boot start location */
    FLASH_SIZE,               /* size */
    PLUGIN_FLAG,              /* Plugin flag*/
    0xFFFFFFFF                /* empty - extra data word */
};

// Config for W25Q64JV with QSPI routed.
__attribute__((section(".boot_hdr.conf")))
const flexspi_nor_config_t qspiflash_config = {
    .pageSize = 256u,
    .sectorSize = 4u * 1024u,
    .ipcmdSerialClkFreq = kFlexSpiSerialClk_30MHz,
    .blockSize = 0x00010000,
    .isUniformBlockSize = false,
    .memConfig =
    {
        .tag = FLEXSPI_CFG_BLK_TAG,
        .version = FLEXSPI_CFG_BLK_VERSION,
        .readSampleClkSrc = kFlexSPIReadSampleClk_LoopbackFromDqsPad,
        .csHoldTime = 3u,
        .csSetupTime = 3u,

        .busyOffset = 0u,     // Status bit 0 indicates busy.
        .busyBitPolarity = 0u,     // Busy when the bit is 1.

        .deviceModeCfgEnable = 1u,
        .deviceModeType = kDeviceConfigCmdType_QuadEnable,
        .deviceModeSeq = {
            .seqId = 4u,
            .seqNum = 1u,
        },
        .deviceModeArg = 0x02,
        .deviceType = kFlexSpiDeviceType_SerialNOR,
        .sflashPadType = kSerialFlash_4Pads,
        .serialClkFreq = kFlexSpiSerialClk_60MHz,
        .sflashA1Size = FLASH_SIZE,
        .lookupTable =
        {
            // FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1)
            // The high 16 bits is command 1 and the low are command 0.
            // Within a command, the top 6 bits are the opcode, the next two are the number
            // of pads and then last byte is the operand. The operand's meaning changes
            // per opcode.

            // Indices with ROM should always have the same function because the ROM
            // bootloader uses it.

            // 0: ROM: Read LUTs
            // Quad version
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0xEB /* the command to send */,
                RADDR_SDR, FLEXSPI_4PAD, 24 /* bits to transmit */),
                FLEXSPI_LUT_SEQ(DUMMY_SDR, FLEXSPI_4PAD, 6 /* 6 dummy cycles, 2 for M7-0 and 4 dummy */,
                    READ_SDR,  FLEXSPI_4PAD, 0x04),
                // Single fast read version, good for debugging.
                // FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0x0B /* the command to send */,
                //                 RADDR_SDR, FLEXSPI_1PAD, 24  /* bits to transmit */),
                // FLEXSPI_LUT_SEQ(DUMMY_SDR, FLEXSPI_1PAD, 8 /* 8 dummy clocks */,
                //                 READ_SDR,  FLEXSPI_1PAD, 0x04),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 1: ROM: Read status
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,  FLEXSPI_1PAD, 0x05 /* the command to send */,
                READ_SDR, FLEXSPI_1PAD, 0x01),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 2: Empty
            EMPTY_SEQUENCE,

            // 3: ROM: Write Enable
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR, FLEXSPI_1PAD, 0x06 /* the command to send */,
                STOP,    FLEXSPI_1PAD, 0x00),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 4: Config: Write Status
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0x31 /* the command to send */,
                WRITE_SDR, FLEXSPI_1PAD, 0x01),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 5: ROM: Erase Sector
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0x20 /* the command to send */,
                RADDR_SDR, FLEXSPI_1PAD, 24 /* bits to transmit */),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 6: Empty
            EMPTY_SEQUENCE,

            // 7: Empty
            EMPTY_SEQUENCE,

            // 8: Block Erase
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0xD8 /* the command to send */,
                RADDR_SDR, FLEXSPI_1PAD, 24 /* bits to transmit */),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 9: ROM: Page program
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR,   FLEXSPI_1PAD, 0x02 /* the command to send */,
                RADDR_SDR, FLEXSPI_1PAD, 24 /* bits to transmit */),

                FLEXSPI_LUT_SEQ(WRITE_SDR, FLEXSPI_1PAD, 0x04 /* data out */,
                    STOP,      FLEXSPI_1PAD, 0),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 10: Empty
            EMPTY_SEQUENCE,

            // 11: ROM: Chip erase
            SEQUENCE(FLEXSPI_LUT_SEQ(CMD_SDR, FLEXSPI_1PAD, 0x60 /* the command to send */,
                STOP,    FLEXSPI_1PAD, 0),
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS,
                TWO_EMPTY_STEPS),

            // 12: Empty
            EMPTY_SEQUENCE,

            // 13: ROM: Read SFDP
            EMPTY_SEQUENCE,

            // 14: ROM: Restore no cmd
            EMPTY_SEQUENCE,

            // 15: ROM: Dummy
            EMPTY_SEQUENCE
        },
    },
};
