|
| 1 | +#define MICROPY_HW_BOARD_NAME "F411DISC" |
| 2 | +#define MICROPY_HW_MCU_NAME "STM32F411" |
| 3 | +#define MICROPY_PY_SYS_PLATFORM "pyboard" |
| 4 | + |
| 5 | +#define MICROPY_HW_HAS_SWITCH (1) |
| 6 | +#define MICROPY_HW_HAS_SDCARD (0) |
| 7 | +#define MICROPY_HW_HAS_MMA7660 (0) |
| 8 | +#define MICROPY_HW_HAS_LIS3DSH (0) |
| 9 | +#define MICROPY_HW_HAS_LCD (0) |
| 10 | +#define MICROPY_HW_ENABLE_RNG (0) |
| 11 | +#define MICROPY_HW_ENABLE_RTC (1) |
| 12 | +#define MICROPY_HW_ENABLE_TIMER (1) |
| 13 | +#define MICROPY_HW_ENABLE_SERVO (1) |
| 14 | +#define MICROPY_HW_ENABLE_DAC (0) |
| 15 | +#define MICROPY_HW_ENABLE_SPI1 (1) |
| 16 | +#define MICROPY_HW_ENABLE_SPI2 (1) |
| 17 | +#define MICROPY_HW_ENABLE_SPI3 (0) |
| 18 | +#define MICROPY_HW_ENABLE_CAN (0) |
| 19 | + |
| 20 | +// HSE is 8MHz |
| 21 | +#define MICROPY_HW_CLK_PLLM (5) |
| 22 | +#define MICROPY_HW_CLK_PLLN (210) |
| 23 | +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4) |
| 24 | +#define MICROPY_HW_CLK_PLLQ (7) |
| 25 | + |
| 26 | +// does not have a 32kHz crystal |
| 27 | +#define MICROPY_HW_RTC_USE_LSE (0) |
| 28 | + |
| 29 | +// UART config |
| 30 | +#define MICROPY_HW_UART1_PORT (GPIOA) |
| 31 | +#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10) |
| 32 | +#define MICROPY_HW_UART2_PORT (GPIOA) |
| 33 | +#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3) |
| 34 | +#define MICROPY_HW_UART2_RTS (GPIO_PIN_1) |
| 35 | +#define MICROPY_HW_UART2_CTS (GPIO_PIN_0) |
| 36 | +#define MICROPY_HW_UART6_PORT (GPIOC) |
| 37 | +#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7) |
| 38 | + |
| 39 | +// I2C busses |
| 40 | +#define MICROPY_HW_I2C1_SCL (pin_B6) |
| 41 | +#define MICROPY_HW_I2C1_SDA (pin_B7) |
| 42 | +//#define MICROPY_HW_I2C2_SCL (pin_B10) |
| 43 | +//#define MICROPY_HW_I2C2_SDA (pin_B11) |
| 44 | +#define MICROPY_HW_I2C3_SCL (pin_A8) |
| 45 | +#define MICROPY_HW_I2C3_SDA (pin_A9) |
| 46 | + |
| 47 | +// USRSW is pulled low. Pressing the button makes the input go high. |
| 48 | +#define MICROPY_HW_USRSW_PIN (pin_A0) |
| 49 | +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) |
| 50 | +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) |
| 51 | +#define MICROPY_HW_USRSW_PRESSED (1) |
| 52 | + |
| 53 | +// LEDs |
| 54 | +#define MICROPY_HW_LED1 (pin_D14) // red |
| 55 | +#define MICROPY_HW_LED2 (pin_D12) // green |
| 56 | +#define MICROPY_HW_LED3 (pin_D13) // orange |
| 57 | +#define MICROPY_HW_LED4 (pin_D15) // blue |
| 58 | +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) |
| 59 | +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) |
| 60 | +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) |
| 61 | + |
| 62 | +// USB config |
| 63 | +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) |
| 64 | +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) |
0 commit comments