| 1 | // SPDX-License-Identifier: GPL-2.0-only |
| 2 | /* |
| 3 | * Driver for keys on GPIO lines capable of generating interrupts. |
| 4 | * |
| 5 | * Copyright 2005 Phil Blundell |
| 6 | * Copyright 2010, 2011 David Jander <david@protonic.nl> |
| 7 | */ |
| 8 | |
| 9 | #include <linux/module.h> |
| 10 | |
| 11 | #include <linux/hrtimer.h> |
| 12 | #include <linux/init.h> |
| 13 | #include <linux/fs.h> |
| 14 | #include <linux/interrupt.h> |
| 15 | #include <linux/irq.h> |
| 16 | #include <linux/sched.h> |
| 17 | #include <linux/pm.h> |
| 18 | #include <linux/slab.h> |
| 19 | #include <linux/sysctl.h> |
| 20 | #include <linux/proc_fs.h> |
| 21 | #include <linux/delay.h> |
| 22 | #include <linux/platform_device.h> |
| 23 | #include <linux/input.h> |
| 24 | #include <linux/gpio_keys.h> |
| 25 | #include <linux/workqueue.h> |
| 26 | #include <linux/gpio.h> |
| 27 | #include <linux/gpio/consumer.h> |
| 28 | #include <linux/of.h> |
| 29 | #include <linux/of_irq.h> |
| 30 | #include <linux/spinlock.h> |
| 31 | #include <dt-bindings/input/gpio-keys.h> |
| 32 | |
| 33 | struct gpio_button_data { |
| 34 | const struct gpio_keys_button *button; |
| 35 | struct input_dev *input; |
| 36 | struct gpio_desc *gpiod; |
| 37 | |
| 38 | unsigned short *code; |
| 39 | |
| 40 | struct hrtimer release_timer; |
| 41 | unsigned int release_delay; /* in msecs, for IRQ-only buttons */ |
| 42 | |
| 43 | struct delayed_work work; |
| 44 | struct hrtimer debounce_timer; |
| 45 | unsigned int software_debounce; /* in msecs, for GPIO-driven buttons */ |
| 46 | |
| 47 | unsigned int irq; |
| 48 | unsigned int wakeirq; |
| 49 | unsigned int wakeup_trigger_type; |
| 50 | |
| 51 | spinlock_t lock; |
| 52 | bool disabled; |
| 53 | bool key_pressed; |
| 54 | bool suspended; |
| 55 | bool debounce_use_hrtimer; |
| 56 | }; |
| 57 | |
| 58 | struct gpio_keys_drvdata { |
| 59 | const struct gpio_keys_platform_data *pdata; |
| 60 | struct input_dev *input; |
| 61 | struct mutex disable_lock; |
| 62 | unsigned short *keymap; |
| 63 | struct gpio_button_data data[]; |
| 64 | }; |
| 65 | |
| 66 | /* |
| 67 | * SYSFS interface for enabling/disabling keys and switches: |
| 68 | * |
| 69 | * There are 4 attributes under /sys/devices/platform/gpio-keys/ |
| 70 | * keys [ro] - bitmap of keys (EV_KEY) which can be |
| 71 | * disabled |
| 72 | * switches [ro] - bitmap of switches (EV_SW) which can be |
| 73 | * disabled |
| 74 | * disabled_keys [rw] - bitmap of keys currently disabled |
| 75 | * disabled_switches [rw] - bitmap of switches currently disabled |
| 76 | * |
| 77 | * Userland can change these values and hence disable event generation |
| 78 | * for each key (or switch). Disabling a key means its interrupt line |
| 79 | * is disabled. |
| 80 | * |
| 81 | * For example, if we have following switches set up as gpio-keys: |
| 82 | * SW_DOCK = 5 |
| 83 | * SW_CAMERA_LENS_COVER = 9 |
| 84 | * SW_KEYPAD_SLIDE = 10 |
| 85 | * SW_FRONT_PROXIMITY = 11 |
| 86 | * This is read from switches: |
| 87 | * 11-9,5 |
| 88 | * Next we want to disable proximity (11) and dock (5), we write: |
| 89 | * 11,5 |
| 90 | * to file disabled_switches. Now proximity and dock IRQs are disabled. |
| 91 | * This can be verified by reading the file disabled_switches: |
| 92 | * 11,5 |
| 93 | * If we now want to enable proximity (11) switch we write: |
| 94 | * 5 |
| 95 | * to disabled_switches. |
| 96 | * |
| 97 | * We can disable only those keys which don't allow sharing the irq. |
| 98 | */ |
| 99 | |
| 100 | /** |
| 101 | * get_n_events_by_type() - returns maximum number of events per @type |
| 102 | * @type: type of button (%EV_KEY, %EV_SW) |
| 103 | * |
| 104 | * Return value of this function can be used to allocate bitmap |
| 105 | * large enough to hold all bits for given type. |
| 106 | */ |
| 107 | static int get_n_events_by_type(int type) |
| 108 | { |
| 109 | BUG_ON(type != EV_SW && type != EV_KEY); |
| 110 | |
| 111 | return (type == EV_KEY) ? KEY_CNT : SW_CNT; |
| 112 | } |
| 113 | |
| 114 | /** |
| 115 | * get_bm_events_by_type() - returns bitmap of supported events per @type |
| 116 | * @dev: input device from which bitmap is retrieved |
| 117 | * @type: type of button (%EV_KEY, %EV_SW) |
| 118 | * |
| 119 | * Return value of this function can be used to allocate bitmap |
| 120 | * large enough to hold all bits for given type. |
| 121 | */ |
| 122 | static const unsigned long *get_bm_events_by_type(struct input_dev *dev, |
| 123 | int type) |
| 124 | { |
| 125 | BUG_ON(type != EV_SW && type != EV_KEY); |
| 126 | |
| 127 | return (type == EV_KEY) ? dev->keybit : dev->swbit; |
| 128 | } |
| 129 | |
| 130 | static void gpio_keys_quiesce_key(void *data) |
| 131 | { |
| 132 | struct gpio_button_data *bdata = data; |
| 133 | |
| 134 | if (!bdata->gpiod) |
| 135 | hrtimer_cancel(timer: &bdata->release_timer); |
| 136 | else if (bdata->debounce_use_hrtimer) |
| 137 | hrtimer_cancel(timer: &bdata->debounce_timer); |
| 138 | else |
| 139 | cancel_delayed_work_sync(dwork: &bdata->work); |
| 140 | } |
| 141 | |
| 142 | /** |
| 143 | * gpio_keys_disable_button() - disables given GPIO button |
| 144 | * @bdata: button data for button to be disabled |
| 145 | * |
| 146 | * Disables button pointed by @bdata. This is done by masking |
| 147 | * IRQ line. After this function is called, button won't generate |
| 148 | * input events anymore. Note that one can only disable buttons |
| 149 | * that don't share IRQs. |
| 150 | * |
| 151 | * Make sure that @bdata->disable_lock is locked when entering |
| 152 | * this function to avoid races when concurrent threads are |
| 153 | * disabling buttons at the same time. |
| 154 | */ |
| 155 | static void gpio_keys_disable_button(struct gpio_button_data *bdata) |
| 156 | { |
| 157 | if (!bdata->disabled) { |
| 158 | /* |
| 159 | * Disable IRQ and associated timer/work structure. |
| 160 | */ |
| 161 | disable_irq(irq: bdata->irq); |
| 162 | gpio_keys_quiesce_key(data: bdata); |
| 163 | bdata->disabled = true; |
| 164 | } |
| 165 | } |
| 166 | |
| 167 | /** |
| 168 | * gpio_keys_enable_button() - enables given GPIO button |
| 169 | * @bdata: button data for button to be disabled |
| 170 | * |
| 171 | * Enables given button pointed by @bdata. |
| 172 | * |
| 173 | * Make sure that @bdata->disable_lock is locked when entering |
| 174 | * this function to avoid races with concurrent threads trying |
| 175 | * to enable the same button at the same time. |
| 176 | */ |
| 177 | static void gpio_keys_enable_button(struct gpio_button_data *bdata) |
| 178 | { |
| 179 | if (bdata->disabled) { |
| 180 | enable_irq(irq: bdata->irq); |
| 181 | bdata->disabled = false; |
| 182 | } |
| 183 | } |
| 184 | |
| 185 | /** |
| 186 | * gpio_keys_attr_show_helper() - fill in stringified bitmap of buttons |
| 187 | * @ddata: pointer to drvdata |
| 188 | * @buf: buffer where stringified bitmap is written |
| 189 | * @type: button type (%EV_KEY, %EV_SW) |
| 190 | * @only_disabled: does caller want only those buttons that are |
| 191 | * currently disabled or all buttons that can be |
| 192 | * disabled |
| 193 | * |
| 194 | * This function writes buttons that can be disabled to @buf. If |
| 195 | * @only_disabled is true, then @buf contains only those buttons |
| 196 | * that are currently disabled. Returns 0 on success or negative |
| 197 | * errno on failure. |
| 198 | */ |
| 199 | static ssize_t gpio_keys_attr_show_helper(struct gpio_keys_drvdata *ddata, |
| 200 | char *buf, unsigned int type, |
| 201 | bool only_disabled) |
| 202 | { |
| 203 | int n_events = get_n_events_by_type(type); |
| 204 | unsigned long *bits; |
| 205 | ssize_t ret; |
| 206 | int i; |
| 207 | |
| 208 | bits = bitmap_zalloc(nbits: n_events, GFP_KERNEL); |
| 209 | if (!bits) |
| 210 | return -ENOMEM; |
| 211 | |
| 212 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 213 | struct gpio_button_data *bdata = &ddata->data[i]; |
| 214 | |
| 215 | if (bdata->button->type != type) |
| 216 | continue; |
| 217 | |
| 218 | if (only_disabled && !bdata->disabled) |
| 219 | continue; |
| 220 | |
| 221 | __set_bit(*bdata->code, bits); |
| 222 | } |
| 223 | |
| 224 | ret = scnprintf(buf, PAGE_SIZE - 1, fmt: "%*pbl" , n_events, bits); |
| 225 | buf[ret++] = '\n'; |
| 226 | buf[ret] = '\0'; |
| 227 | |
| 228 | bitmap_free(bitmap: bits); |
| 229 | |
| 230 | return ret; |
| 231 | } |
| 232 | |
| 233 | /** |
| 234 | * gpio_keys_attr_store_helper() - enable/disable buttons based on given bitmap |
| 235 | * @ddata: pointer to drvdata |
| 236 | * @buf: buffer from userspace that contains stringified bitmap |
| 237 | * @type: button type (%EV_KEY, %EV_SW) |
| 238 | * |
| 239 | * This function parses stringified bitmap from @buf and disables/enables |
| 240 | * GPIO buttons accordingly. Returns 0 on success and negative error |
| 241 | * on failure. |
| 242 | */ |
| 243 | static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata, |
| 244 | const char *buf, unsigned int type) |
| 245 | { |
| 246 | int n_events = get_n_events_by_type(type); |
| 247 | const unsigned long *bitmap = get_bm_events_by_type(dev: ddata->input, type); |
| 248 | ssize_t error; |
| 249 | int i; |
| 250 | |
| 251 | unsigned long *bits __free(bitmap) = bitmap_alloc(nbits: n_events, GFP_KERNEL); |
| 252 | if (!bits) |
| 253 | return -ENOMEM; |
| 254 | |
| 255 | error = bitmap_parselist(buf, maskp: bits, nmaskbits: n_events); |
| 256 | if (error) |
| 257 | return error; |
| 258 | |
| 259 | /* First validate */ |
| 260 | if (!bitmap_subset(src1: bits, src2: bitmap, nbits: n_events)) |
| 261 | return -EINVAL; |
| 262 | |
| 263 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 264 | struct gpio_button_data *bdata = &ddata->data[i]; |
| 265 | |
| 266 | if (bdata->button->type != type) |
| 267 | continue; |
| 268 | |
| 269 | if (test_bit(*bdata->code, bits) && |
| 270 | !bdata->button->can_disable) { |
| 271 | return -EINVAL; |
| 272 | } |
| 273 | } |
| 274 | |
| 275 | guard(mutex)(T: &ddata->disable_lock); |
| 276 | |
| 277 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 278 | struct gpio_button_data *bdata = &ddata->data[i]; |
| 279 | |
| 280 | if (bdata->button->type != type) |
| 281 | continue; |
| 282 | |
| 283 | if (test_bit(*bdata->code, bits)) |
| 284 | gpio_keys_disable_button(bdata); |
| 285 | else |
| 286 | gpio_keys_enable_button(bdata); |
| 287 | } |
| 288 | |
| 289 | return 0; |
| 290 | } |
| 291 | |
| 292 | #define ATTR_SHOW_FN(name, type, only_disabled) \ |
| 293 | static ssize_t gpio_keys_show_##name(struct device *dev, \ |
| 294 | struct device_attribute *attr, \ |
| 295 | char *buf) \ |
| 296 | { \ |
| 297 | struct platform_device *pdev = to_platform_device(dev); \ |
| 298 | struct gpio_keys_drvdata *ddata = platform_get_drvdata(pdev); \ |
| 299 | \ |
| 300 | return gpio_keys_attr_show_helper(ddata, buf, \ |
| 301 | type, only_disabled); \ |
| 302 | } |
| 303 | |
| 304 | ATTR_SHOW_FN(keys, EV_KEY, false); |
| 305 | ATTR_SHOW_FN(switches, EV_SW, false); |
| 306 | ATTR_SHOW_FN(disabled_keys, EV_KEY, true); |
| 307 | ATTR_SHOW_FN(disabled_switches, EV_SW, true); |
| 308 | |
| 309 | /* |
| 310 | * ATTRIBUTES: |
| 311 | * |
| 312 | * /sys/devices/platform/gpio-keys/keys [ro] |
| 313 | * /sys/devices/platform/gpio-keys/switches [ro] |
| 314 | */ |
| 315 | static DEVICE_ATTR(keys, S_IRUGO, gpio_keys_show_keys, NULL); |
| 316 | static DEVICE_ATTR(switches, S_IRUGO, gpio_keys_show_switches, NULL); |
| 317 | |
| 318 | #define ATTR_STORE_FN(name, type) \ |
| 319 | static ssize_t gpio_keys_store_##name(struct device *dev, \ |
| 320 | struct device_attribute *attr, \ |
| 321 | const char *buf, \ |
| 322 | size_t count) \ |
| 323 | { \ |
| 324 | struct platform_device *pdev = to_platform_device(dev); \ |
| 325 | struct gpio_keys_drvdata *ddata = platform_get_drvdata(pdev); \ |
| 326 | ssize_t error; \ |
| 327 | \ |
| 328 | error = gpio_keys_attr_store_helper(ddata, buf, type); \ |
| 329 | if (error) \ |
| 330 | return error; \ |
| 331 | \ |
| 332 | return count; \ |
| 333 | } |
| 334 | |
| 335 | ATTR_STORE_FN(disabled_keys, EV_KEY); |
| 336 | ATTR_STORE_FN(disabled_switches, EV_SW); |
| 337 | |
| 338 | /* |
| 339 | * ATTRIBUTES: |
| 340 | * |
| 341 | * /sys/devices/platform/gpio-keys/disabled_keys [rw] |
| 342 | * /sys/devices/platform/gpio-keys/disables_switches [rw] |
| 343 | */ |
| 344 | static DEVICE_ATTR(disabled_keys, S_IWUSR | S_IRUGO, |
| 345 | gpio_keys_show_disabled_keys, |
| 346 | gpio_keys_store_disabled_keys); |
| 347 | static DEVICE_ATTR(disabled_switches, S_IWUSR | S_IRUGO, |
| 348 | gpio_keys_show_disabled_switches, |
| 349 | gpio_keys_store_disabled_switches); |
| 350 | |
| 351 | static struct attribute *gpio_keys_attrs[] = { |
| 352 | &dev_attr_keys.attr, |
| 353 | &dev_attr_switches.attr, |
| 354 | &dev_attr_disabled_keys.attr, |
| 355 | &dev_attr_disabled_switches.attr, |
| 356 | NULL, |
| 357 | }; |
| 358 | ATTRIBUTE_GROUPS(gpio_keys); |
| 359 | |
| 360 | static void gpio_keys_gpio_report_event(struct gpio_button_data *bdata) |
| 361 | { |
| 362 | const struct gpio_keys_button *button = bdata->button; |
| 363 | struct input_dev *input = bdata->input; |
| 364 | unsigned int type = button->type ?: EV_KEY; |
| 365 | int state; |
| 366 | |
| 367 | state = bdata->debounce_use_hrtimer ? |
| 368 | gpiod_get_value(desc: bdata->gpiod) : |
| 369 | gpiod_get_value_cansleep(desc: bdata->gpiod); |
| 370 | if (state < 0) { |
| 371 | dev_err(input->dev.parent, |
| 372 | "failed to get gpio state: %d\n" , state); |
| 373 | return; |
| 374 | } |
| 375 | |
| 376 | if (type == EV_ABS) { |
| 377 | if (state) |
| 378 | input_event(dev: input, type, code: button->code, value: button->value); |
| 379 | } else { |
| 380 | input_event(dev: input, type, code: *bdata->code, value: state); |
| 381 | } |
| 382 | } |
| 383 | |
| 384 | static void gpio_keys_debounce_event(struct gpio_button_data *bdata) |
| 385 | { |
| 386 | gpio_keys_gpio_report_event(bdata); |
| 387 | input_sync(dev: bdata->input); |
| 388 | |
| 389 | if (bdata->button->wakeup) |
| 390 | pm_relax(dev: bdata->input->dev.parent); |
| 391 | } |
| 392 | |
| 393 | static void gpio_keys_gpio_work_func(struct work_struct *work) |
| 394 | { |
| 395 | struct gpio_button_data *bdata = |
| 396 | container_of(work, struct gpio_button_data, work.work); |
| 397 | |
| 398 | gpio_keys_debounce_event(bdata); |
| 399 | } |
| 400 | |
| 401 | static enum hrtimer_restart gpio_keys_debounce_timer(struct hrtimer *t) |
| 402 | { |
| 403 | struct gpio_button_data *bdata = |
| 404 | container_of(t, struct gpio_button_data, debounce_timer); |
| 405 | |
| 406 | gpio_keys_debounce_event(bdata); |
| 407 | |
| 408 | return HRTIMER_NORESTART; |
| 409 | } |
| 410 | |
| 411 | static irqreturn_t gpio_keys_gpio_isr(int irq, void *dev_id) |
| 412 | { |
| 413 | struct gpio_button_data *bdata = dev_id; |
| 414 | |
| 415 | BUG_ON(irq != bdata->irq); |
| 416 | |
| 417 | if (bdata->button->wakeup) { |
| 418 | const struct gpio_keys_button *button = bdata->button; |
| 419 | |
| 420 | pm_stay_awake(dev: bdata->input->dev.parent); |
| 421 | if (bdata->suspended && |
| 422 | (button->type == 0 || button->type == EV_KEY)) { |
| 423 | /* |
| 424 | * Simulate wakeup key press in case the key has |
| 425 | * already released by the time we got interrupt |
| 426 | * handler to run. |
| 427 | */ |
| 428 | input_report_key(dev: bdata->input, code: button->code, value: 1); |
| 429 | } |
| 430 | } |
| 431 | |
| 432 | if (bdata->debounce_use_hrtimer) { |
| 433 | hrtimer_start(timer: &bdata->debounce_timer, |
| 434 | tim: ms_to_ktime(ms: bdata->software_debounce), |
| 435 | mode: HRTIMER_MODE_REL); |
| 436 | } else { |
| 437 | mod_delayed_work(wq: system_wq, |
| 438 | dwork: &bdata->work, |
| 439 | delay: msecs_to_jiffies(m: bdata->software_debounce)); |
| 440 | } |
| 441 | |
| 442 | return IRQ_HANDLED; |
| 443 | } |
| 444 | |
| 445 | static enum hrtimer_restart gpio_keys_irq_timer(struct hrtimer *t) |
| 446 | { |
| 447 | struct gpio_button_data *bdata = container_of(t, |
| 448 | struct gpio_button_data, |
| 449 | release_timer); |
| 450 | struct input_dev *input = bdata->input; |
| 451 | |
| 452 | guard(spinlock_irqsave)(l: &bdata->lock); |
| 453 | |
| 454 | if (bdata->key_pressed) { |
| 455 | input_report_key(dev: input, code: *bdata->code, value: 0); |
| 456 | input_sync(dev: input); |
| 457 | bdata->key_pressed = false; |
| 458 | } |
| 459 | |
| 460 | return HRTIMER_NORESTART; |
| 461 | } |
| 462 | |
| 463 | static irqreturn_t gpio_keys_irq_isr(int irq, void *dev_id) |
| 464 | { |
| 465 | struct gpio_button_data *bdata = dev_id; |
| 466 | struct input_dev *input = bdata->input; |
| 467 | |
| 468 | BUG_ON(irq != bdata->irq); |
| 469 | |
| 470 | guard(spinlock_irqsave)(l: &bdata->lock); |
| 471 | |
| 472 | if (!bdata->key_pressed) { |
| 473 | if (bdata->button->wakeup) |
| 474 | pm_wakeup_event(dev: bdata->input->dev.parent, msec: 0); |
| 475 | |
| 476 | input_report_key(dev: input, code: *bdata->code, value: 1); |
| 477 | input_sync(dev: input); |
| 478 | |
| 479 | if (!bdata->release_delay) { |
| 480 | input_report_key(dev: input, code: *bdata->code, value: 0); |
| 481 | input_sync(dev: input); |
| 482 | goto out; |
| 483 | } |
| 484 | |
| 485 | bdata->key_pressed = true; |
| 486 | } |
| 487 | |
| 488 | if (bdata->release_delay) |
| 489 | hrtimer_start(timer: &bdata->release_timer, |
| 490 | tim: ms_to_ktime(ms: bdata->release_delay), |
| 491 | mode: HRTIMER_MODE_REL); |
| 492 | out: |
| 493 | return IRQ_HANDLED; |
| 494 | } |
| 495 | |
| 496 | static int gpio_keys_setup_key(struct platform_device *pdev, |
| 497 | struct input_dev *input, |
| 498 | struct gpio_keys_drvdata *ddata, |
| 499 | const struct gpio_keys_button *button, |
| 500 | int idx, |
| 501 | struct fwnode_handle *child) |
| 502 | { |
| 503 | const char *desc = button->desc ? button->desc : "gpio_keys" ; |
| 504 | struct device *dev = &pdev->dev; |
| 505 | struct gpio_button_data *bdata = &ddata->data[idx]; |
| 506 | irq_handler_t isr; |
| 507 | unsigned long irqflags; |
| 508 | const char *wakedesc; |
| 509 | int irq; |
| 510 | int error; |
| 511 | |
| 512 | bdata->input = input; |
| 513 | bdata->button = button; |
| 514 | spin_lock_init(&bdata->lock); |
| 515 | |
| 516 | if (child) { |
| 517 | bdata->gpiod = devm_fwnode_gpiod_get(dev, fwnode: child, |
| 518 | NULL, flags: GPIOD_IN, label: desc); |
| 519 | if (IS_ERR(ptr: bdata->gpiod)) { |
| 520 | error = PTR_ERR(ptr: bdata->gpiod); |
| 521 | if (error != -ENOENT) |
| 522 | return dev_err_probe(dev, err: error, |
| 523 | fmt: "failed to get gpio\n" ); |
| 524 | |
| 525 | /* |
| 526 | * GPIO is optional, we may be dealing with |
| 527 | * purely interrupt-driven setup. |
| 528 | */ |
| 529 | bdata->gpiod = NULL; |
| 530 | } |
| 531 | } else if (gpio_is_valid(number: button->gpio)) { |
| 532 | /* |
| 533 | * Legacy GPIO number, so request the GPIO here and |
| 534 | * convert it to descriptor. |
| 535 | */ |
| 536 | error = devm_gpio_request_one(dev, gpio: button->gpio, GPIOF_IN, label: desc); |
| 537 | if (error < 0) { |
| 538 | dev_err(dev, "Failed to request GPIO %d, error %d\n" , |
| 539 | button->gpio, error); |
| 540 | return error; |
| 541 | } |
| 542 | |
| 543 | bdata->gpiod = gpio_to_desc(gpio: button->gpio); |
| 544 | if (!bdata->gpiod) |
| 545 | return -EINVAL; |
| 546 | |
| 547 | if (button->active_low ^ gpiod_is_active_low(desc: bdata->gpiod)) |
| 548 | gpiod_toggle_active_low(desc: bdata->gpiod); |
| 549 | } |
| 550 | |
| 551 | if (bdata->gpiod) { |
| 552 | bool active_low = gpiod_is_active_low(desc: bdata->gpiod); |
| 553 | |
| 554 | if (button->debounce_interval) { |
| 555 | error = gpiod_set_debounce(desc: bdata->gpiod, |
| 556 | debounce: button->debounce_interval * 1000); |
| 557 | /* use timer if gpiolib doesn't provide debounce */ |
| 558 | if (error < 0) |
| 559 | bdata->software_debounce = |
| 560 | button->debounce_interval; |
| 561 | |
| 562 | /* |
| 563 | * If reading the GPIO won't sleep, we can use a |
| 564 | * hrtimer instead of a standard timer for the software |
| 565 | * debounce, to reduce the latency as much as possible. |
| 566 | */ |
| 567 | bdata->debounce_use_hrtimer = |
| 568 | !gpiod_cansleep(desc: bdata->gpiod); |
| 569 | } |
| 570 | |
| 571 | /* |
| 572 | * If an interrupt was specified, use it instead of the gpio |
| 573 | * interrupt and use the gpio for reading the state. A separate |
| 574 | * interrupt may be used as the main button interrupt for |
| 575 | * runtime PM to detect events also in deeper idle states. If a |
| 576 | * dedicated wakeirq is used for system suspend only, see below |
| 577 | * for bdata->wakeirq setup. |
| 578 | */ |
| 579 | if (button->irq) { |
| 580 | bdata->irq = button->irq; |
| 581 | } else { |
| 582 | irq = gpiod_to_irq(desc: bdata->gpiod); |
| 583 | if (irq < 0) { |
| 584 | error = irq; |
| 585 | dev_err_probe(dev, err: error, |
| 586 | fmt: "Unable to get irq number for GPIO %d\n" , |
| 587 | button->gpio); |
| 588 | return error; |
| 589 | } |
| 590 | bdata->irq = irq; |
| 591 | } |
| 592 | |
| 593 | INIT_DELAYED_WORK(&bdata->work, gpio_keys_gpio_work_func); |
| 594 | |
| 595 | hrtimer_setup(timer: &bdata->debounce_timer, function: gpio_keys_debounce_timer, |
| 596 | CLOCK_REALTIME, mode: HRTIMER_MODE_REL); |
| 597 | |
| 598 | isr = gpio_keys_gpio_isr; |
| 599 | irqflags = IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING; |
| 600 | |
| 601 | switch (button->wakeup_event_action) { |
| 602 | case EV_ACT_ASSERTED: |
| 603 | bdata->wakeup_trigger_type = active_low ? |
| 604 | IRQ_TYPE_EDGE_FALLING : IRQ_TYPE_EDGE_RISING; |
| 605 | break; |
| 606 | case EV_ACT_DEASSERTED: |
| 607 | bdata->wakeup_trigger_type = active_low ? |
| 608 | IRQ_TYPE_EDGE_RISING : IRQ_TYPE_EDGE_FALLING; |
| 609 | break; |
| 610 | case EV_ACT_ANY: |
| 611 | default: |
| 612 | /* |
| 613 | * For other cases, we are OK letting suspend/resume |
| 614 | * not reconfigure the trigger type. |
| 615 | */ |
| 616 | break; |
| 617 | } |
| 618 | } else { |
| 619 | if (!button->irq) { |
| 620 | dev_err(dev, "Found button without gpio or irq\n" ); |
| 621 | return -EINVAL; |
| 622 | } |
| 623 | |
| 624 | bdata->irq = button->irq; |
| 625 | |
| 626 | if (button->type && button->type != EV_KEY) { |
| 627 | dev_err(dev, "Only EV_KEY allowed for IRQ buttons.\n" ); |
| 628 | return -EINVAL; |
| 629 | } |
| 630 | |
| 631 | bdata->release_delay = button->debounce_interval; |
| 632 | hrtimer_setup(timer: &bdata->release_timer, function: gpio_keys_irq_timer, |
| 633 | CLOCK_REALTIME, mode: HRTIMER_MODE_REL); |
| 634 | |
| 635 | isr = gpio_keys_irq_isr; |
| 636 | irqflags = 0; |
| 637 | |
| 638 | /* |
| 639 | * For IRQ buttons, there is no interrupt for release. |
| 640 | * So we don't need to reconfigure the trigger type for wakeup. |
| 641 | */ |
| 642 | } |
| 643 | |
| 644 | bdata->code = &ddata->keymap[idx]; |
| 645 | *bdata->code = button->code; |
| 646 | input_set_capability(dev: input, type: button->type ?: EV_KEY, code: *bdata->code); |
| 647 | |
| 648 | /* |
| 649 | * Install custom action to cancel release timer and |
| 650 | * workqueue item. |
| 651 | */ |
| 652 | error = devm_add_action(dev, gpio_keys_quiesce_key, bdata); |
| 653 | if (error) { |
| 654 | dev_err(dev, "failed to register quiesce action, error: %d\n" , |
| 655 | error); |
| 656 | return error; |
| 657 | } |
| 658 | |
| 659 | /* |
| 660 | * If platform has specified that the button can be disabled, |
| 661 | * we don't want it to share the interrupt line. |
| 662 | */ |
| 663 | if (!button->can_disable) |
| 664 | irqflags |= IRQF_SHARED; |
| 665 | |
| 666 | error = devm_request_any_context_irq(dev, irq: bdata->irq, handler: isr, irqflags, |
| 667 | devname: desc, dev_id: bdata); |
| 668 | if (error < 0) { |
| 669 | dev_err(dev, "Unable to claim irq %d; error %d\n" , |
| 670 | bdata->irq, error); |
| 671 | return error; |
| 672 | } |
| 673 | |
| 674 | if (!button->wakeirq) |
| 675 | return 0; |
| 676 | |
| 677 | /* Use :wakeup suffix like drivers/base/power/wakeirq.c does */ |
| 678 | wakedesc = devm_kasprintf(dev, GFP_KERNEL, fmt: "%s:wakeup" , desc); |
| 679 | if (!wakedesc) |
| 680 | return -ENOMEM; |
| 681 | |
| 682 | bdata->wakeirq = button->wakeirq; |
| 683 | irqflags |= IRQF_NO_SUSPEND; |
| 684 | |
| 685 | /* |
| 686 | * Wakeirq shares the handler with the main interrupt, it's only |
| 687 | * active during system suspend. See gpio_keys_button_enable_wakeup() |
| 688 | * and gpio_keys_button_disable_wakeup(). |
| 689 | */ |
| 690 | error = devm_request_any_context_irq(dev, irq: bdata->wakeirq, handler: isr, |
| 691 | irqflags, devname: wakedesc, dev_id: bdata); |
| 692 | if (error < 0) { |
| 693 | dev_err(dev, "Unable to claim wakeirq %d; error %d\n" , |
| 694 | bdata->irq, error); |
| 695 | return error; |
| 696 | } |
| 697 | |
| 698 | /* |
| 699 | * Disable wakeirq until suspend. IRQF_NO_AUTOEN won't work if |
| 700 | * IRQF_SHARED was set based on !button->can_disable. |
| 701 | */ |
| 702 | disable_irq(irq: bdata->wakeirq); |
| 703 | |
| 704 | return 0; |
| 705 | } |
| 706 | |
| 707 | static void gpio_keys_report_state(struct gpio_keys_drvdata *ddata) |
| 708 | { |
| 709 | struct input_dev *input = ddata->input; |
| 710 | int i; |
| 711 | |
| 712 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 713 | struct gpio_button_data *bdata = &ddata->data[i]; |
| 714 | if (bdata->gpiod) |
| 715 | gpio_keys_gpio_report_event(bdata); |
| 716 | } |
| 717 | input_sync(dev: input); |
| 718 | } |
| 719 | |
| 720 | static int gpio_keys_open(struct input_dev *input) |
| 721 | { |
| 722 | struct gpio_keys_drvdata *ddata = input_get_drvdata(dev: input); |
| 723 | const struct gpio_keys_platform_data *pdata = ddata->pdata; |
| 724 | int error; |
| 725 | |
| 726 | if (pdata->enable) { |
| 727 | error = pdata->enable(input->dev.parent); |
| 728 | if (error) |
| 729 | return error; |
| 730 | } |
| 731 | |
| 732 | /* Report current state of buttons that are connected to GPIOs */ |
| 733 | gpio_keys_report_state(ddata); |
| 734 | |
| 735 | return 0; |
| 736 | } |
| 737 | |
| 738 | static void gpio_keys_close(struct input_dev *input) |
| 739 | { |
| 740 | struct gpio_keys_drvdata *ddata = input_get_drvdata(dev: input); |
| 741 | const struct gpio_keys_platform_data *pdata = ddata->pdata; |
| 742 | |
| 743 | if (pdata->disable) |
| 744 | pdata->disable(input->dev.parent); |
| 745 | } |
| 746 | |
| 747 | /* |
| 748 | * Handlers for alternative sources of platform_data |
| 749 | */ |
| 750 | |
| 751 | /* |
| 752 | * Translate properties into platform_data |
| 753 | */ |
| 754 | static struct gpio_keys_platform_data * |
| 755 | gpio_keys_get_devtree_pdata(struct device *dev) |
| 756 | { |
| 757 | struct gpio_keys_platform_data *pdata; |
| 758 | struct gpio_keys_button *button; |
| 759 | int nbuttons, irq; |
| 760 | |
| 761 | nbuttons = device_get_child_node_count(dev); |
| 762 | if (nbuttons == 0) |
| 763 | return ERR_PTR(error: -ENODEV); |
| 764 | |
| 765 | pdata = devm_kzalloc(dev, |
| 766 | size: sizeof(*pdata) + nbuttons * sizeof(*button), |
| 767 | GFP_KERNEL); |
| 768 | if (!pdata) |
| 769 | return ERR_PTR(error: -ENOMEM); |
| 770 | |
| 771 | button = (struct gpio_keys_button *)(pdata + 1); |
| 772 | |
| 773 | pdata->buttons = button; |
| 774 | pdata->nbuttons = nbuttons; |
| 775 | |
| 776 | pdata->rep = device_property_read_bool(dev, propname: "autorepeat" ); |
| 777 | |
| 778 | device_property_read_string(dev, propname: "label" , val: &pdata->name); |
| 779 | |
| 780 | device_for_each_child_node_scoped(dev, child) { |
| 781 | if (is_of_node(fwnode: child)) { |
| 782 | irq = of_irq_get_byname(to_of_node(child), name: "irq" ); |
| 783 | if (irq > 0) |
| 784 | button->irq = irq; |
| 785 | |
| 786 | irq = of_irq_get_byname(to_of_node(child), name: "wakeup" ); |
| 787 | if (irq > 0) |
| 788 | button->wakeirq = irq; |
| 789 | |
| 790 | if (!button->irq && !button->wakeirq) |
| 791 | button->irq = |
| 792 | irq_of_parse_and_map(to_of_node(child), index: 0); |
| 793 | } |
| 794 | |
| 795 | if (fwnode_property_read_u32(fwnode: child, propname: "linux,code" , |
| 796 | val: &button->code)) { |
| 797 | dev_err(dev, "Button without keycode\n" ); |
| 798 | return ERR_PTR(error: -EINVAL); |
| 799 | } |
| 800 | |
| 801 | fwnode_property_read_string(fwnode: child, propname: "label" , val: &button->desc); |
| 802 | |
| 803 | if (fwnode_property_read_u32(fwnode: child, propname: "linux,input-type" , |
| 804 | val: &button->type)) |
| 805 | button->type = EV_KEY; |
| 806 | |
| 807 | fwnode_property_read_u32(fwnode: child, propname: "linux,input-value" , |
| 808 | val: (u32 *)&button->value); |
| 809 | |
| 810 | button->wakeup = |
| 811 | fwnode_property_read_bool(fwnode: child, propname: "wakeup-source" ) || |
| 812 | /* legacy name */ |
| 813 | fwnode_property_read_bool(fwnode: child, propname: "gpio-key,wakeup" ); |
| 814 | |
| 815 | fwnode_property_read_u32(fwnode: child, propname: "wakeup-event-action" , |
| 816 | val: &button->wakeup_event_action); |
| 817 | |
| 818 | button->can_disable = |
| 819 | fwnode_property_read_bool(fwnode: child, propname: "linux,can-disable" ); |
| 820 | |
| 821 | if (fwnode_property_read_u32(fwnode: child, propname: "debounce-interval" , |
| 822 | val: &button->debounce_interval)) |
| 823 | button->debounce_interval = 5; |
| 824 | |
| 825 | button++; |
| 826 | } |
| 827 | |
| 828 | return pdata; |
| 829 | } |
| 830 | |
| 831 | static const struct of_device_id gpio_keys_of_match[] = { |
| 832 | { .compatible = "gpio-keys" , }, |
| 833 | { }, |
| 834 | }; |
| 835 | MODULE_DEVICE_TABLE(of, gpio_keys_of_match); |
| 836 | |
| 837 | static int gpio_keys_probe(struct platform_device *pdev) |
| 838 | { |
| 839 | struct device *dev = &pdev->dev; |
| 840 | const struct gpio_keys_platform_data *pdata = dev_get_platdata(dev); |
| 841 | struct fwnode_handle *child = NULL; |
| 842 | struct gpio_keys_drvdata *ddata; |
| 843 | struct input_dev *input; |
| 844 | int i, error; |
| 845 | int wakeup = 0; |
| 846 | |
| 847 | if (!pdata) { |
| 848 | pdata = gpio_keys_get_devtree_pdata(dev); |
| 849 | if (IS_ERR(ptr: pdata)) |
| 850 | return PTR_ERR(ptr: pdata); |
| 851 | } |
| 852 | |
| 853 | ddata = devm_kzalloc(dev, struct_size(ddata, data, pdata->nbuttons), |
| 854 | GFP_KERNEL); |
| 855 | if (!ddata) { |
| 856 | dev_err(dev, "failed to allocate state\n" ); |
| 857 | return -ENOMEM; |
| 858 | } |
| 859 | |
| 860 | ddata->keymap = devm_kcalloc(dev, |
| 861 | n: pdata->nbuttons, size: sizeof(ddata->keymap[0]), |
| 862 | GFP_KERNEL); |
| 863 | if (!ddata->keymap) |
| 864 | return -ENOMEM; |
| 865 | |
| 866 | input = devm_input_allocate_device(dev); |
| 867 | if (!input) { |
| 868 | dev_err(dev, "failed to allocate input device\n" ); |
| 869 | return -ENOMEM; |
| 870 | } |
| 871 | |
| 872 | ddata->pdata = pdata; |
| 873 | ddata->input = input; |
| 874 | mutex_init(&ddata->disable_lock); |
| 875 | |
| 876 | platform_set_drvdata(pdev, data: ddata); |
| 877 | input_set_drvdata(dev: input, data: ddata); |
| 878 | |
| 879 | input->name = pdata->name ? : pdev->name; |
| 880 | input->phys = "gpio-keys/input0" ; |
| 881 | input->dev.parent = dev; |
| 882 | input->open = gpio_keys_open; |
| 883 | input->close = gpio_keys_close; |
| 884 | |
| 885 | input->id.bustype = BUS_HOST; |
| 886 | input->id.vendor = 0x0001; |
| 887 | input->id.product = 0x0001; |
| 888 | input->id.version = 0x0100; |
| 889 | |
| 890 | input->keycode = ddata->keymap; |
| 891 | input->keycodesize = sizeof(ddata->keymap[0]); |
| 892 | input->keycodemax = pdata->nbuttons; |
| 893 | |
| 894 | /* Enable auto repeat feature of Linux input subsystem */ |
| 895 | if (pdata->rep) |
| 896 | __set_bit(EV_REP, input->evbit); |
| 897 | |
| 898 | for (i = 0; i < pdata->nbuttons; i++) { |
| 899 | const struct gpio_keys_button *button = &pdata->buttons[i]; |
| 900 | |
| 901 | if (!dev_get_platdata(dev)) { |
| 902 | child = device_get_next_child_node(dev, child); |
| 903 | if (!child) { |
| 904 | dev_err(dev, |
| 905 | "missing child device node for entry %d\n" , |
| 906 | i); |
| 907 | return -EINVAL; |
| 908 | } |
| 909 | } |
| 910 | |
| 911 | error = gpio_keys_setup_key(pdev, input, ddata, |
| 912 | button, idx: i, child); |
| 913 | if (error) { |
| 914 | fwnode_handle_put(fwnode: child); |
| 915 | return error; |
| 916 | } |
| 917 | |
| 918 | if (button->wakeup) |
| 919 | wakeup = 1; |
| 920 | } |
| 921 | |
| 922 | fwnode_handle_put(fwnode: child); |
| 923 | |
| 924 | error = input_register_device(input); |
| 925 | if (error) { |
| 926 | dev_err(dev, "Unable to register input device, error: %d\n" , |
| 927 | error); |
| 928 | return error; |
| 929 | } |
| 930 | |
| 931 | device_init_wakeup(dev, enable: wakeup); |
| 932 | |
| 933 | return 0; |
| 934 | } |
| 935 | |
| 936 | static int __maybe_unused |
| 937 | gpio_keys_button_enable_wakeup(struct gpio_button_data *bdata) |
| 938 | { |
| 939 | int error; |
| 940 | |
| 941 | error = enable_irq_wake(irq: bdata->irq); |
| 942 | if (error) { |
| 943 | dev_err(bdata->input->dev.parent, |
| 944 | "failed to configure IRQ %d as wakeup source: %d\n" , |
| 945 | bdata->irq, error); |
| 946 | return error; |
| 947 | } |
| 948 | |
| 949 | if (bdata->wakeup_trigger_type) { |
| 950 | error = irq_set_irq_type(irq: bdata->irq, |
| 951 | type: bdata->wakeup_trigger_type); |
| 952 | if (error) { |
| 953 | dev_err(bdata->input->dev.parent, |
| 954 | "failed to set wakeup trigger %08x for IRQ %d: %d\n" , |
| 955 | bdata->wakeup_trigger_type, bdata->irq, error); |
| 956 | disable_irq_wake(irq: bdata->irq); |
| 957 | return error; |
| 958 | } |
| 959 | } |
| 960 | |
| 961 | if (bdata->wakeirq) { |
| 962 | enable_irq(irq: bdata->wakeirq); |
| 963 | disable_irq(irq: bdata->irq); |
| 964 | } |
| 965 | |
| 966 | return 0; |
| 967 | } |
| 968 | |
| 969 | static void __maybe_unused |
| 970 | gpio_keys_button_disable_wakeup(struct gpio_button_data *bdata) |
| 971 | { |
| 972 | int error; |
| 973 | |
| 974 | if (bdata->wakeirq) { |
| 975 | enable_irq(irq: bdata->irq); |
| 976 | disable_irq(irq: bdata->wakeirq); |
| 977 | } |
| 978 | |
| 979 | /* |
| 980 | * The trigger type is always both edges for gpio-based keys and we do |
| 981 | * not support changing wakeup trigger for interrupt-based keys. |
| 982 | */ |
| 983 | if (bdata->wakeup_trigger_type) { |
| 984 | error = irq_set_irq_type(irq: bdata->irq, type: IRQ_TYPE_EDGE_BOTH); |
| 985 | if (error) |
| 986 | dev_warn(bdata->input->dev.parent, |
| 987 | "failed to restore interrupt trigger for IRQ %d: %d\n" , |
| 988 | bdata->irq, error); |
| 989 | } |
| 990 | |
| 991 | error = disable_irq_wake(irq: bdata->irq); |
| 992 | if (error) |
| 993 | dev_warn(bdata->input->dev.parent, |
| 994 | "failed to disable IRQ %d as wake source: %d\n" , |
| 995 | bdata->irq, error); |
| 996 | } |
| 997 | |
| 998 | static int __maybe_unused |
| 999 | gpio_keys_enable_wakeup(struct gpio_keys_drvdata *ddata) |
| 1000 | { |
| 1001 | struct gpio_button_data *bdata; |
| 1002 | int error; |
| 1003 | int i; |
| 1004 | |
| 1005 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 1006 | bdata = &ddata->data[i]; |
| 1007 | if (bdata->button->wakeup) { |
| 1008 | error = gpio_keys_button_enable_wakeup(bdata); |
| 1009 | if (error) |
| 1010 | goto err_out; |
| 1011 | } |
| 1012 | bdata->suspended = true; |
| 1013 | } |
| 1014 | |
| 1015 | return 0; |
| 1016 | |
| 1017 | err_out: |
| 1018 | while (i--) { |
| 1019 | bdata = &ddata->data[i]; |
| 1020 | if (bdata->button->wakeup) |
| 1021 | gpio_keys_button_disable_wakeup(bdata); |
| 1022 | bdata->suspended = false; |
| 1023 | } |
| 1024 | |
| 1025 | return error; |
| 1026 | } |
| 1027 | |
| 1028 | static void __maybe_unused |
| 1029 | gpio_keys_disable_wakeup(struct gpio_keys_drvdata *ddata) |
| 1030 | { |
| 1031 | struct gpio_button_data *bdata; |
| 1032 | int i; |
| 1033 | |
| 1034 | for (i = 0; i < ddata->pdata->nbuttons; i++) { |
| 1035 | bdata = &ddata->data[i]; |
| 1036 | bdata->suspended = false; |
| 1037 | if (irqd_is_wakeup_set(d: irq_get_irq_data(irq: bdata->irq))) |
| 1038 | gpio_keys_button_disable_wakeup(bdata); |
| 1039 | } |
| 1040 | } |
| 1041 | |
| 1042 | static int gpio_keys_suspend(struct device *dev) |
| 1043 | { |
| 1044 | struct gpio_keys_drvdata *ddata = dev_get_drvdata(dev); |
| 1045 | struct input_dev *input = ddata->input; |
| 1046 | int error; |
| 1047 | |
| 1048 | if (device_may_wakeup(dev)) { |
| 1049 | error = gpio_keys_enable_wakeup(ddata); |
| 1050 | if (error) |
| 1051 | return error; |
| 1052 | } else { |
| 1053 | guard(mutex)(T: &input->mutex); |
| 1054 | |
| 1055 | if (input_device_enabled(dev: input)) |
| 1056 | gpio_keys_close(input); |
| 1057 | } |
| 1058 | |
| 1059 | return 0; |
| 1060 | } |
| 1061 | |
| 1062 | static int gpio_keys_resume(struct device *dev) |
| 1063 | { |
| 1064 | struct gpio_keys_drvdata *ddata = dev_get_drvdata(dev); |
| 1065 | struct input_dev *input = ddata->input; |
| 1066 | int error; |
| 1067 | |
| 1068 | if (device_may_wakeup(dev)) { |
| 1069 | gpio_keys_disable_wakeup(ddata); |
| 1070 | } else { |
| 1071 | guard(mutex)(T: &input->mutex); |
| 1072 | |
| 1073 | if (input_device_enabled(dev: input)) { |
| 1074 | error = gpio_keys_open(input); |
| 1075 | if (error) |
| 1076 | return error; |
| 1077 | } |
| 1078 | } |
| 1079 | |
| 1080 | gpio_keys_report_state(ddata); |
| 1081 | return 0; |
| 1082 | } |
| 1083 | |
| 1084 | static DEFINE_SIMPLE_DEV_PM_OPS(gpio_keys_pm_ops, gpio_keys_suspend, gpio_keys_resume); |
| 1085 | |
| 1086 | static void gpio_keys_shutdown(struct platform_device *pdev) |
| 1087 | { |
| 1088 | int ret; |
| 1089 | |
| 1090 | ret = gpio_keys_suspend(dev: &pdev->dev); |
| 1091 | if (ret) |
| 1092 | dev_err(&pdev->dev, "failed to shutdown\n" ); |
| 1093 | } |
| 1094 | |
| 1095 | static struct platform_driver gpio_keys_device_driver = { |
| 1096 | .probe = gpio_keys_probe, |
| 1097 | .shutdown = gpio_keys_shutdown, |
| 1098 | .driver = { |
| 1099 | .name = "gpio-keys" , |
| 1100 | .pm = pm_sleep_ptr(&gpio_keys_pm_ops), |
| 1101 | .of_match_table = gpio_keys_of_match, |
| 1102 | .dev_groups = gpio_keys_groups, |
| 1103 | } |
| 1104 | }; |
| 1105 | |
| 1106 | static int __init gpio_keys_init(void) |
| 1107 | { |
| 1108 | return platform_driver_register(&gpio_keys_device_driver); |
| 1109 | } |
| 1110 | |
| 1111 | static void __exit gpio_keys_exit(void) |
| 1112 | { |
| 1113 | platform_driver_unregister(&gpio_keys_device_driver); |
| 1114 | } |
| 1115 | |
| 1116 | late_initcall(gpio_keys_init); |
| 1117 | module_exit(gpio_keys_exit); |
| 1118 | |
| 1119 | MODULE_LICENSE("GPL" ); |
| 1120 | MODULE_AUTHOR("Phil Blundell <pb@handhelds.org>" ); |
| 1121 | MODULE_DESCRIPTION("Keyboard driver for GPIOs" ); |
| 1122 | MODULE_ALIAS("platform:gpio-keys" ); |
| 1123 | |